EasyManuals Logo

Fagor CNC 8055i Manual

Fagor CNC 8055i
166 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #57 background imageLoading...
Page #57 background image
NEW FEATURES
Page i / iii
CNC 8055 / CNC 8055i
INDEX
Version V9.01
1 New hard disk and Ethernet................................................................................................1
1.1 Configuration ................................................................................................................3
1.2 Modified variables ........................................................................................................5
1.3 Modified programming instructions ..............................................................................5
1.4 Hard disk diagnosis ......................................................................................................6
1.5 Diagnosis of the Ethernet configuration .......................................................................7
1.6 Connection to a PC through WinDNC ..........................................................................8
1.7 Connection to the network through FTPserver.............................................................9
1.8 Format of the program................................................................................................11
2 CARDA slot as floppy disk drive .......................................................................................12
3 Telediagnosis ....................................................................................................................14
3.1 Disable the CNC screen and keyboard from the PC..................................................14
3.2 Telephone call from the CNC .....................................................................................14
4 Tandem axes ....................................................................................................................15
4.1 Block diagram.............................................................................................................16
4.2 Control of the tandem axis .........................................................................................17
4.3 Machine parameter setting.........................................................................................20
4.4 Variables ....................................................................................................................22
4.5 Tandem adjustment....................................................................................................22
5 Incline axis management ..................................................................................................25
6 Additive coupling between axes ........................................................................................28
6.1 Configuration ..............................................................................................................29
6.2 PLC program ..............................................................................................................29
7 TCP management on rotary table .....................................................................................30
8 Tool change ......................................................................................................................33
8.1 Stop block preparation when executing a new T........................................................33
8.2 New treatment of CYCLE STOP during the execution of a T.....................................33
9 Modification of the operation of the feedrate when it is F0................................................34
10 The cross compensation on gantry axes affects the slave axis ........................................34
11 Subroutines associated with M41, M42, M43, M44 ..........................................................35
12 Probe input selection.........................................................................................................35
13 Programming in radius or diameter...................................................................................35
14 Program G2 and G3 without the center coordinates (I, J, K) ............................................36
15 Changing the kinematics by program................................................................................36
16 Modifications in PLC operation .........................................................................................36
16.1 Initializing the PLC outputs while compiling the program ...........................................36
16.2 Ending the execution of a block using a PLC mark ....................................................37
16.3 "Rapid" key controlled by PLC in execution and simulation .......................................38
16.4 Name the logic inputs and outputs with the axis name ..............................................39
17 New marks to park spindles ..............................................................................................39
18 Modifications and new variables .......................................................................................40
19 Parameters accessible from the oscilloscope or OEM subroutine ....................................41
20 MC model. ISO programming assistance .........................................................................41
20.1 Zero offsets and presets.............................................................................................42
20.2 Work zones ................................................................................................................42
20.3 Place labels and repetitions from label to label ..........................................................43
20.4 Mirror image ...............................................................................................................43
20.5 Scaling factor..............................................................................................................43
20.6 Coordinate rotation.....................................................................................................44
21 MC model. Zero offset table management........................................................................44
22 MC model. Accessing cycles and programs from the auxiliary screen .............................45
23 MC model. In case of error in a cycle, point to the erroneous cycle. ................................45
24 MC model. Display name and number of the cycle...........................................................45
25 MC model. Highlighting the axis being moved in jog or with handwheels.........................46
26 MC model. Copying a profile.............................................................................................46
27 MC model. Select a program by indicating its number......................................................46

Table of Contents

Other manuals for Fagor CNC 8055i

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fagor CNC 8055i and is the answer not in the manual?

Fagor CNC 8055i Specifications

General IconGeneral
BrandFagor
ModelCNC 8055i
CategoryPower Tool
LanguageEnglish

Related product manuals