What to do if my FBD Beverage Dispenser shows Error #130: Board Failure?
If your FBD Beverage Dispenser displays Error #130 indicating 'Board Failure', where the control board is not functioning properly, you can try the following: * Cycle the power to the dispenser to see if it will clear the error. * Replace the control board.
What does error #450: Gas #1 - High Regulated CO2 PSI mean on my FBD Beverage Dispenser and how to resolve it?
Error #450 'Gas #1 - High Regulated CO2 PSI' on your FBD Beverage Dispenser indicates that the regulated CO2 pressure is above 70 PSIG (483 kPag). Check the 'Gas 1' regulator on the header tray and ensure it is set to 60 PSIG (414 kPag).
What should I do if my FBD Beverage Dispenser displays Error #070: Compressor Ran Too Long?
If your FBD Beverage Dispenser displays Error #070 'Compressor Ran Too Long', it means the compressor ran continuously for more than 90 minutes. Here's what you can do: * If the location is an extreme volume venue such as a festival, contact FBD service for instructions on adjusting the timer. * Run the refrigeration diagnostic sequence to determine the reason for the failure.
What does error #200: Return Temperature Sensor mean on my FBD Beverage Dispenser and how do I fix it?
Error #200 'Return Temperature Sensor' on your FBD Beverage Dispenser indicates that the refrigeration return (suction) temperature sensor is not reading correctly. To fix it: * Ensure the temperature sensor is plugged in. * Replace the sensor if faulty.
What does error #190: HPSI Transducer mean on my FBD Beverage Dispenser and how can I resolve it?
Error #190 'HPSI Transducer' on your FBD Beverage Dispenser indicates that the high side refrigeration pressure is not reading correctly. To resolve this: * Ensure the pressure transducer is plugged in. * Replace the transducer if faulty.
What to do if the FBD Beverage Dispenser shows 'Syrup Out' error #011, 012, 013, 014?
If the FBD Beverage Dispenser displays a 'Syrup Out' error, it indicates that the syrup pressure is less than 45 PSIG (310 kPag), especially for the base syrup in multi-flavor dispensers. Here's what you should do: * Replace the empty BIB (Bag-In-Box). * Ensure the gas line is properly connected to the BIB pump. * Check that the BIB pump is operating correctly. * Make sure the gas tank is not empty. * Verify the syrup shutoff valve at the solution module is turned on. * Confirm that any syrup shutoff valves at the back of the dispenser are not turned off. * Ensure the syrup supply pressure at the dispenser reads 70 PSIG (483 kPag), adjusting the regulator if necessary. * Check that the syrup pressure transducer is connected and working properly.
What does error #340: Flavor Add-On Board Missing mean on my FBD Beverage Dispenser and what should I do?
Error #340 'Flavor Add-On Board Missing' on your FBD Beverage Dispenser indicates that the dispenser cannot detect the flavor add-on board because the board is missing or damaged. To resolve this: * Ensure the software matches the dispenser’s hardware configuration. * Ensure the flavor add-on board is installed and seated properly on the control board. * Replace the flavor add-on board if faulty.
What does error #1000: Gas #2 - Low Regulated N2 PSI mean on my FBD Beverage Dispenser and how to fix it?
Error #1000 'Gas #2 - Low Regulated N2 PSI' on your FBD Beverage Dispenser means that the regulated N2 pressure dropped below 50 PSIG (345 kPag). To fix it: * Ensure the N2 supply is not low. * Check the 'Gas 2' regulator on the header tray and ensure it is set to 60 PSIG (414 kPag).
What does error #460: Gas #1 - Low Regulated N2 PSI mean on my FBD Beverage Dispenser and how to fix it?
Error #460 'Gas #1 - Low Regulated N2 PSI' on your FBD Beverage Dispenser means that the regulated N2 pressure dropped below 50 PSIG (345 kPag). To fix it: * Ensure the N2 supply is not low. * Check the 'Gas 1' regulator on the header tray and ensure it is set to 60 PSIG (414 kPag).
What does error #480: Gas #2 - Low Regulated CO2 PSI mean on my FBD Beverage Dispenser and how to fix it?
Error #480 'Gas #2 - Low Regulated CO2 PSI' on your FBD Beverage Dispenser means that the regulated CO2 pressure dropped below 50 PSIG (345 kPag). To fix it: * Ensure the CO2 supply is not low. * Check the 'Gas 2' regulator on the header tray and ensure it is set to 60 PSIG (414 kPag).
General| Brand | FBD |
|---|---|
| Model | 373 |
| Category | Beverage Dispenser |
| Language | English |
To Next Page
