What does 'Low Line Voltage' mean on my FBD 772 Beverage Dispenser?
If your FBD Beverage Dispenser displays 'Low Line Voltage', install a boost transformer. Even if the voltage is slightly above 200 V, a boost transformer may be needed as fluctuations in power during the day or during unit operation may cause it to drop below 200 volts and shut down the unit, because the voltage supply may be below 200 volts.
How to fix 'Syrup Out' on FBD 772?
To address a 'Syrup Out' error on your FBD Beverage Dispenser, first, replace the empty BIB. Then, make sure the CO2 line is properly connected to the BIB pump and that the pump is functioning correctly. Check that the CO2 tank isn't empty and that the syrup shutoff valve at the solution module is turned on. Also, ensure any syrup shutoff valves at the back of the unit are not turned off. Verify that the syrup supply pressure at the dispenser reads 70 PSI, adjusting the regulator if necessary. Finally, confirm that the syrup pressure transducer is connected and working properly, because the syrup pressure may be less than 45 PSI.
What does 'LPSI transducer' mean on FBD 772?
If your FBD Beverage Dispenser displays 'LPSI transducer', ensure the pressure transducer is plugged in. Replace the transducer if faulty, because low side refrigeration pressure may not be reading correctly.
What does 'HPSI transducer' mean on FBD 772 Beverage Dispenser?
If your FBD Beverage Dispenser displays 'HPSI transducer', ensure the pressure transducer is plugged in. Replace the transducer if faulty, because high side refrigeration pressure may not be reading correctly.
What does 'Return Temperature Sensor' mean on FBD 772?
If your FBD Beverage Dispenser displays 'Return Temperature Sensor', ensure the temperature sensor is plugged in. Replace the sensor if faulty, because the refrigeration return (suction) temperature sensor may not be reading correctly.
What does 'Refrigeration Malfunction' mean on FBD Beverage Dispenser?
If your FBD Beverage Dispenser displays 'Refrigeration Malfunction', run the fill diagnostic sequence to determine the reason for the failure, because refrigeration pressures may not be in the correct range.
How to fix 'Refrigeration Pressure Transducer Offset' on FBD 772 Beverage Dispenser?
If your FBD Beverage Dispenser displays 'Refrigeration Pressure Transducer Offset', attach a set of refrigeration gauges that are known to be accurate and then compare the gauges to the readings on the LCD. Replace the pressure transducer that is reading incorrect, because pressure transducers may not be reading correctly during the refrigeration diagnostic test.
What to do if the fan is not turning on in my FBD Beverage Dispenser?
If the fan is not turning on your FBD Beverage Dispenser: 1. Remove control board and check for a blown fan fuse (F1 and F2). If a fuse is blown then a fan or capacitor malfunction may be possible. 2. If fuses are OK, reinstall control board. 3. Disconnect wiring harnesses at fan capacitor. 4. Manually turn fan on and check for line voltage (230V) between the connectors removed from the capacitor. If no voltage is present then replace control board. 5. If correct voltage is present then substitute a “known to be good” capacitor and try to operate fan again. If fan fails to start with good capacitor then replace both fan and capacitor.
How to troubleshoot a 'Refrigeration solenoid stuck open' on my FBD 772 Beverage Dispenser?
To troubleshoot a 'Refrigeration solenoid stuck open' on your FBD Beverage Dispenser: 1. Verify the solenoid is not activated by going to the Manual ON/OFF. 2. Remove wiring from the suspect solenoid and check for 24 VAC. Note: The voltage will read ~19 VAC when not powered. 3. If no voltage (~19 VAC) then replace the solenoid valve. 4. If 24 VAC is present then replace the control board.
How to troubleshoot 'Excessive refrigeration pressure' on my FBD Beverage Dispenser?
To troubleshoot 'Excessive refrigeration pressure' on your FBD Beverage Dispenser: 1. Disconnect the electrical harness from the CO2 solenoid for the barrel in question. 2. Manually activate the solenoid and check to make sure there is 12 VDC at the connection. Note: The voltage will read ~2 VDC when not powered. 3. If no voltage then replace the control board. 4. If correct voltage is present then replace the solenoid. Be sure to turn off CO2 supply before disconnecting the CO2 line from the solenoid. 5. If solenoid is functioning properly then a leak may be present in the product delivery system. Check the relief valve, dispensing valve, rear seal and tubing in the product tray for leaks. If no leaks are found then the tank pressure transducer may be defective.
Ensures proper grounding and safe electrical connections for the dispenser to prevent shock.
Details safety procedures for handling compressed gases like CO2 and N2 to prevent hazards.
Provides guidance on dispenser weight, lifting, and maintaining an upright position during handling.
Lists required pressures, clearances, and refrigerant type for dispenser installation.
Details operational voltage, frequency, and current ratings for different dispenser models.
Specifies ideal indoor location criteria, including level surface and adequate space.
Describes countertop mounting methods, including flush and leg-based installations.
Details multi-gas capabilities and gas types for 771/772 models.
Guide to connecting potable water, including backflow prevention devices.
Instructions for connecting gas supply, regulator settings, and shutoff valves.
Guidelines for syrup line connections, tubing size, and pressure considerations.
Procedure for checking all connections for leaks and priming the beverage lines.
Importance of defrosting and scheduling options to maintain optimal drink texture.
Understanding factors affecting drink quality and adjustable electronic settings.
Overview of the keypad buttons and their functions for controlling the dispenser.
Accessing and interpreting logged fault codes for troubleshooting.
Procedure for accessing specialized menus for trained service technicians.
Sections for barrel purging, filling, draining, and calibration procedures.
Adjusting serial number, display units, and active charge settings.
Setting up gas types and configuring drink expansion for multi-flavor models.
Modifying the amount of gas in the drink for texture and foam control.
Adjusting the freezing level of the product for desired consistency.
Fine-tuning the gas level (expansion) for optimal drink characteristics.
Modifying the product's frozen state for ideal texture and consistency.
Running system diagnostics for refrigeration, beater, and fill circuits.
Step-by-step guide for sanitizing the dispenser's internal beverage pathways.
Recommended annual maintenance tasks for optimal dispenser performance.
Understanding and responding to messages displayed on the dispenser's home screen.
Explanation of fault code structure and meanings for diagnostics.
Diagnosing compressor startup failures, checking contactors and capacitors.
General| Brand | FBD |
|---|---|
| Model | 772 |
| Category | Beverage Dispenser |
| Language | English |
To Next Page
