FENDT 1290 UD - Machine Identification and Plates; Component Identification Diagrams; Service and Lubrication Procedures; Tractor Connection and Setup

1.3.1.15 Knotter lubrication pump specificat
ions ............................. 1-26
1.3.1.16 Chain lubrication pump specifications ...............................1-26
1.3.1.17 Lubricants and capacities ....................................... 1-26
1.3.1.18 Tire specifications ............................................. 1-27
1.3.1.19 Brake specifications ........................................... 1-28
1.3.1.20 Maximum speed ..............................................1-28
1.3.1.21 Tractor requirements ........................................... 1-28
1.3.1.22 Noise level .................................................. 1-28
1.3.2 Bolt torque values ................................................... 1-28
1.4 Machine indentification ................................................ 1-31
1.4.1 Location of the serial number plates and the statutory plates - if necessary .......... 1-31
1.4.2 Serial number description .............................................. 1-32
1.5 Machine component views ............................................ 1-33
1.5.1 Outside view - left side ............................................... 1-33
1.5.2 Outside view - right side .............................................. 1-34
1.5.3 Inner view - left side ..................................................1-35
1.5.4 Inner view - right side ................................................. 1-36
1.5.5 Outside view - top ...................................................1-37
1.5.6 Outside view - bottom ................................................ 1-38
1.6 Service and lubrication schedule ....................................... 1-39
1.6.1 Service schedule .................................................... 1-39
1.6.2 Lubrication procedures and general information .............................. 1-42
1.6.2.1 Drive chains ................................................. 1-42
1.6.2.2 Driveline lubrication and maintenance .............................. 1-43
1.6.2.3 Lubricate the hitch ball, if equipped ................................ 1-45
1.6.2.4 Do not lubricate the overrunning clutch ............................. 1-45
1.6.2.5 Do not lubricate the slip clutch for the main drive ...................... 1-46
1.6.2.6 Lubricate the connecting rods .................................... 1-46
1.6.2.7 Examine the packer crank bearings ................................ 1-46
1.6.2.8 Lubricate the bearing for the main drive sprocket ...................... 1-47
1.6.2.9 Lubricate the stuer drive ....................................... 1-47
1.6.2.10 Lubricate the knotter/needle clutch arm and the clutch arm roller .......... 1-47
1.6.2.11 Lubricate the brake linkages ..................................... 1-48
1.6.2.12 Lubricate the steering axle pivots and the steering axle tie-rods ............1-48
1.6.2.13 Lubricate the pivot bushings for the tandem axle springs ................ 1-49
1.6.2.14 Lubricate the center fitting for the six twine knotter .................... 1-49
1.6.2.15 Lubricate the linkages for the bale density cylinders .................... 1-49
1.6.2.16 Lubricate the packer clutch bushing and the splines .................... 1-50
1.7 Connect to the tractor - CE ............................................. 1-51
1.7.1 Hitch component identification .......................................... 1-51
1.7.2 Set the tongue height .................................................1-51
1.7.3 Tractor setup dimensions with an 80 mm (3.15 in) ball hitch, a CE spherical ball hitch, or
a 50 mm (2 in) ring hitch .................................................... 1-52
1.7.4 Connect a 50 mm (2 in) ring hitch to the tractor .............................. 1-52
1.7.5 Connect an 80 mm (3.15 in) ball hitch to the tractor ........................... 1-53
1.7.6 Operate a manual jack installed on the tongue ............................... 1-53
1.7.7 Operate a hydraulic jack installed on the tongue .............................. 1-54
1.7.8 Install the safety transport chain ......................................... 1-55
1.7.9 Constant velocity implement driveline, if equipped ............................ 1-55
1.7.9.1 Check the constant velocity implement driveline for correct length ......... 1-55
1.7.9.2 Connect a constant velocity implement driveline to a power take-o (PTO) .... 1-57
1.7.9.3 Adjust the pedestal gearbox ..................................... 1-58
1.8 Checklists ............................................................ 1-59
1.8.1 Daily checklist ...................................................... 1-59
1.8.2 Examine after the first hour of operation ................................... 1-59
1.9 Lamps and Reflectors .................................................. 1-61
1.9.1 Lamps and reflectors ................................................. 1-61
Table of contents
1-2 Large Square B
aler
79037317B
Find manuals at https://best-manuals.com