First Office HEIGHT ADJUSTABLE TABLE User Manual

1. Panel
2. Initialization Procedure
The initalization procedure must be completed before the first running table after the
table is installed or parts replaced.
•
Press and Hold & simultaneously for more than 3 seconds, the legs begin to move
down at half speed of normal operation.
•
Keep pressing the & , notice the legs move down to the lowest position and rebound
2-5 mm, then stop.
•
Then release & together, the initialization process is complete.
3. Move Up & Down
•
Press and Hold and the legs move up.
•
Release and the legs stop.
•
Press and Hold and the legs move down.
•
Release and the legs stop.
4. Set Memory Positions
•
Press and Hold & , then release and run the legs to the position you want the table surface to be.
•
Click button S, and then click button 1 , 2 , or 3 within next 3 seconds, this is how you save the positions.
5. Move to the Memorized Positions
•
Press and hold the button 1 , 2 , or 3, and the legs will return to corresponding positions saved.
6. Verify the Display Switch Data to Table Height
Check the switch display format in inches or centimeters and toggle to the unit you like and match
to the actual measurement. In inches format, the minimum adjustable height is 0.5 inches, while in
centimeters format is 1 centimeter.
•
Set the table at any height (reccommended at the bottom position), measure the table actual height
and write down the number in inches or in centimeters.
•
Press and Hold the button S, then press and hold , keep for about 3 seconds. The first number should
start flashing on the screen.
•
Release the buttons and click on either or to change the first number. The first number is being
increased or decreased to the first number you measured.
•
Click button S and the second number should start flashing on the screen.
•
Click or to change the number, the second number is being increased or decreased to the second
number you measured.
•
Click button S, the third number should start flashing on the screen.
•
Click or to change the number, The third number is being increased or decreased to the third
number you measured.
•
Click button S, completed.
DIGITAL HANDSET OPERATION
OPERATION INSTRUCTIONS
RANGE
INSTRUCTION SHEET #2577INS
PART #1730534
•
1 Button: Preset 1
•
2 Button: Preset 2
•
Display: Reads in
1
/
2
"
Increments
•
3 Button: Preset 3
•
S Button: Select

First Office HEIGHT ADJUSTABLE TABLE Specifications

General

Brand	First Office
Model	HEIGHT ADJUSTABLE TABLE
Category	Indoor Furnishing
Language	English

Summary

Digital Handset Operation

Panel Overview

Details the buttons and display functions of the digital handset.

Initialization Procedure

Steps to initialize the table legs for proper operation.

Manual Height Adjustment

Instructions for moving the table up and down.

Memory Position Settings

How to set and save preferred table height positions.

Recalling Memorized Positions

How to move the table to saved height settings.

Display Data Verification

Calibrating the display to match the actual table height.

Height Adjustable Bench Kit Assembly

Attach Frame Components

Connect cross tubes and strut tube to leg columns.

Assemble Bench Frame Halves

Connect leg assemblies and cross bars for bench halves.

Install Spanner Bars

Insert and secure spanner bars into bench cross tubes.

Join Bench Assembly Halves

Connect the two bench assembly halves using spanner bars.

Cable Carrier Assembly

Adjust Benching Frame

Adjust frame for cable carrier width and leave one end loose.

Attach Cable Carrier

Secure carrier to cross bars using bolts.

Final Tightening

Tighten remaining spanner bar set screws after carrier attachment.

Ganging Tray and Rail Installation

Ganging Tray Assembly

Insert and attach ganging tray into cable carrier.

Ganging Rail Assembly

Install thumb screw brackets into rail and bench cross bar.

Height Adjustable Return Frame Kit Assembly

Attach Frame Components

Connect cross tubes and strut tube to leg columns.

Insert Spanner Bars

Insert spanner bars into end tubes and secure.

Attach Mount Plate

Secure mount plate to end tubes using machine screws.

Attach Return Frame to Bench

Align and secure return frame assembly to bench kit.

Cable Entry Pole Assembly

Mounting Locations

Attach pole to ganging tray or cable carrier in 3 locations.

Secure Housing

Align housing holes and secure with self-tapping screws.

Access Panel Installation

Install removable access panel for cable routing.

Worksurface Installation (24"D & 30"D)

Align Worksurface

Place worksurface and align pre-drilled holes with strut tubes.

Verify Alignment

Check offset distances for proper location and alignment.

Attach Worksurface

Secure worksurface using wood screws into strut and cross tubes.

Return Top Assembly

Position Return Top

Place return top onto frame, aligning with worksurface edges.

Check Frame Adjustment

Verify overhang and frame center positioning.

Attach Return Top

Secure return top using clamp plates and wood screws.

Worksurface Edge Modesty Installation

Attach Brackets to Panel

Attach specified brackets to the modesty panel.

Mount Modesty Panel

Attach the assembled modesty panel to the worksurface edge.

Rail Mounted Privacy Screen Installation

Prepare Standoffs

Remove nut and washer from each standoff.

Position Screen

Align screen standoffs with holes in the cable carrier.

Secure Screen

Attach washer and nut to standoff bolts through access hole.

Height Adjustable Table Assembly

Assemble Leg and Foot

Attach foot to leg column with hex socket screws.

Install Leveling Glides

Insert leveling glides into the bottom of the foot.

Create LH/RH Assemblies

Repeat steps to create left and right leg assemblies.

Attach Spanner Bars

Slide and secure short mounting tubes onto spanner bars.

Attach Cross Tubes

Secure cross tubes to spanner bars.

Install End Tubes

Insert screw guides into end tubes and attach to leg assemblies.

Attach Table Top

Position and secure the table top to the assembled frame.

Attach U-Clamps

Secure frame to top using U-clamps on cross bars.