Need help?Do you have a question about the Flight Dental Systems Clave 23+ and is the answer not in the manual?
General| Type | Autoclave |
|---|---|
| Chamber Volume | 23 liters |
| Frequency | 50/60 Hz |
| Sterilization Time | 4-30 minutes |
| Material | Stainless Steel |
| Capacity | 23 liters |
| Voltage | 220-240 V |
| Sterilization Temperature Range | 121°C to 134°C |
| Safety Features | Overheat protection |
Explains the maintenance symbol and error code E88 requiring dealer contact.
Notes the need to replace the bacteria filter approximately every 3 months.
Intended use fields, sterilization temperatures, and adherence to international standards.
Explains symbols for grounding, hot surfaces, and general safety notices.
Mentions product testing against CAN/CSA-C22.2 No. 61010-1.
Details chamber size, voltage, circuit breaker, and nominal power.
Lists sterilization temperatures, water capacity, and operating temperature range.
Covers exterior dimensions, weight, noise, humidity, and atmospheric pressure.
Lists all items provided in the sterilizer package.
Specifies required ventilation space and level work table placement.
Advises against covering vents, blocking doors, or installing near water/heat.
Steps for opening the door, connecting power, and powering on the device.
Details information shown on the LCD, including door status, water level, and program.
Notifies users to refill the distilled water tank when the low water icon appears.
Guidelines for instrument placement, spacing, and preventing water pooling in containers.
Advice on wrapping instruments and ensuring material compatibility.
Reminder not to exceed the stated weight limit for trays.
Explains the functions of the LCD, Select, Up, Down, and Start buttons.
How to access and choose from the available sterilization programs.
Instructions for placing sterilized items onto the tray and into the chamber.
Proper procedure for closing and locking the door, including alarm conditions.
How to start the cycle and typical cycle duration.
Explains the indicator for an incompletely closed door before cycle start.
Steps to highlight and select "Basic Set" for parameter adjustments.
How to modify values using buttons and save changes.
Explains the function of the cycle counter and its non-editable nature.
How to select "Report" to view a list of past sterilization cycles.
Steps to select and send records to the printer and USB port.
Procedure to enter advanced settings by holding the SELECT button for 5 seconds.
How to adjust holding time and drying time parameters for cycles.
How to adjust ambient pressure for operation in high-altitude locations.
How to choose display units for pressure and temperature.
How to enable or disable the preheat option for sterilization cycles.
How to use a USB drive to store sterilization cycle reports automatically.
Procedures for daily cleaning of seal/surface and weekly cleaning of tanks/chamber.
Includes cleaning filters and replacing bacteria/door seals at specified intervals.
Specific steps for weekly cleaning of the water tank, chamber, and door seal.
Procedure to tighten the door seal using a spanner tool if steam leaks occur.
Step-by-step guide for removing and installing a new door seal.
Warning to ensure the chamber and door have cooled before replacing the seal.
Details error codes for temperature, pressure, and door lock issues with solutions.
Explains errors for pressure leaks, door lock, heating elements, and manual cycle end.
Covers pressure issues and manual cycle end for the Plus version.
Procedures for powering off, unplugging, and draining tanks before moving or storage.
Specifies temperature, humidity, and pressure requirements for safe storage.
Mandates strapping the unit to a pallet for secure shipping.
Explains circuit breaker, thermal cutouts for electrical protection.
Covers safety valve, door micro-switch, and door safety lock.
Details thermal switches for heating elements and self-leveling pressure system.
Lists acceptable limits for residue, silica, iron, cadmium, lead, etc. in feed water.
Lists acceptable limits for residue, silica, iron, cadmium, etc. in condensate.
Describes visual appearance and hardness limits for feed water and condensate.
Details temperature, pressure, time, type, and load for these cycles.
Provides data for wrapped, textile, and prion sterilization cycles, including types and loads.
Information on the optional drying cycle time and sterilizer ready time.
States the maximum operating temperatures for 134°C and 121°C cycles.
Shows connections for chamber heater, steam heater, and thermal protector.
Illustrates connections for water pump, air compressor, fan, and printer/USB ports.
Details connections for pressure sensor, door switch, and various valves (V1, V4).
Lists and defines temperature and pressure sensors (TP1, TP2, TP3).
Shows major components like safety valve, door lock valve, steam generator, and chamber.
Illustrates the flow of distilled water, used water, air compressor, and condenser.
Identifies air release valve (V1) and water release valve (V4) with part numbers.
Details the two-year warranty period for autoclaves and exclusions.
Lists items and conditions not covered, such as labor, misuse, and wear items.
Instructions for activating the warranty and contacting customer service.
Information on who pays for transportation and repair arrangements.
Provides email and phone numbers for sales and marketing inquiries.
Lists phone numbers for technical support assistance.
Provides phone numbers for parts and warranty-related questions.
Gives the office address for mail and shipping purposes.
To Next Page
