Flotec Multi-Stage Pump

Questions and Answers

C
Cheryl MartinezJul 26, 2025
Why is air spurting from my Flotec Water Pump faucets?
- R
  Robin DunlapJul 26, 2025
  If you're experiencing air spurts from your Flotec Water Pump faucets, it could be that the pump is picking up prime; when the pump picks up prime, all air will be ejected. Another cause could be a leak in the suction side of the pump, meaning the suction pipe is sucking air. Finally, it could be intermittent over-pumping of the well (water drawn down below the foot valve); check the joints.
W
Wesley MejiaJul 30, 2025
What to do if my Flotec Multi-Stage Pump Water Pump motor will not run?
- D
  Derrick AguirreJul 31, 2025
  If your Flotec Water Pump motor isn't running, first, ensure the disconnect switch is on. If that's not the issue, check for a blown fuse and replace it if necessary. Other potential causes include a defective starting switch (in which case, disconnect power and replace the switch, referring to wiring instructions), loose or incorrectly wired wires at the motor (disconnect power and tighten all wiring), or dirty pressure switch contacts (disconnect power and file the contacts).
A
Amy WilliamsAug 4, 2025
Why does my Flotec Water Pump motor run but no water is delivered?
- T
  Timothy GriffithAug 4, 2025
  If your Flotec Water Pump motor runs but no water is delivered, several issues could be the cause. If it's a new installation, the pump may not have picked up its prime, so re-prime it according to the instructions. Check for air leaks in all connections on the suction line, AVC, and jet. A leaking foot valve could also be the problem, so replace it if necessary. Other potential causes include the pump losing its prime (check connections on the suction line and shaft seal), a water level below the suction of the pump (lower the suction line and re-prime), a plugged jet or impeller (clean according to instructions), a stuck check valve or foot valve (replace), frozen pipes (thaw them), or a foot valve/strainer buried in sand or mud (raise it above the well bottom).
K
Kimberly CampbellAug 12, 2025
Why does my Flotec Multi-Stage Pump deliver water but does not shut off?
- D
  Dorothy PittmanAug 12, 2025
  If your Flotec Water Pump delivers water but doesn't shut off, the pressure switch might be out of adjustment or the contacts are 'frozen'; in this case, disconnect power and adjust or replace the pressure switch. Also, check if any faucets have been left open and close them. A clogged venturi, nozzle, or impeller could also be the cause; clean these components. Finally, the water level in the well might be lower than estimated; check the possibility of using a deep well jet pump.
C
Christina DavisAug 17, 2025
Why is my Flotec Multi-Stage Pump motor running hot and the overload is kicking off?
- D
  Debra RodgersAug 17, 2025
  If your Flotec Water Pump motor runs hot and the overload kicks off, it could be due to the motor being wired incorrectly; refer to the wiring instructions. Another possibility is that the voltage is too low; check with your power company. Lastly, the pump might be cycling too frequently; install heavier wiring if the current wire size is too small (refer to the Electrical / Wiring Chart).
S
Shannon JoyceAug 21, 2025
Why does my Flotec Multi-Stage Pump not deliver water to full capacity?
- R
  Rhonda SmithAug 21, 2025
  If your Flotec Water Pump isn't delivering water to its full capacity, the water level in the well might be lower than estimated; consider a deep well jet pump if the water level is over 25 ft. Also, if steel piping is used, it may be corroded or limed, causing excess friction; replace it with plastic pipe where possible, or with new steel pipe. Finally, the discharge piping might be too small; use larger discharge piping.
M
Michael TaylorNov 7, 2025
What to do if my Flotec Multi-Stage Pump Water Pump cycles too frequently?
- M
  Megan RamosNov 7, 2025
  If your Flotec Water Pump cycles too frequently, the standard pressure tank might be waterlogged with no air cushion; drain the tank to the air volume control port. Alternatively, there could be leaks in the pipes; check for air leaks at any connection. Other possible causes include open faucets or valves (close them), leaking foot valves (replace the foot valve), a pressure switch out of adjustment (adjust or replace the pressure switch), or an air charge that is too low in the pre-charged tank. To address the last one: # Disconnect power. # Open faucets until all pressure is relieved. # Use a tire pressure gauge to check the air pressure in the tank at the valve stem. # If it's less than the pressure switch cut-in setting (40 PSI), pump air into the tank until the air pressure is 2...