Frick SGXH-4021 - Page 14

070.650-IOM (JUL 19)
Page 14
SGC/SGX ROTARY SCREW COMPRESSOR
INSTALLATION
Figure 5: Port locations, SGC 2321
506.5 [19.94]
SC-6
SL-2
SB-3
SD-1
658.4 [25.92]
SC-14
SC-5
382.5 [15.06]
166.6 [6.56]
108 [4.25]
SE-1
292.1 [11.50]
85.1 [3.35]
85.1 [3.35]
M
F
635 [25.00]
317.5 [12.50]
P
T
693.5 [27.30]
SB-2
P
SB-2
Ă381 [Ă15.00]
66.8 [2.63]
68.3 [2.69]
243.2 [9.58]
260.4 [10.25]
97.3 [3.83]
100.4 [3.95]
35.1 [1.38]
75 [2.95]
257.3 [10.13]
173 [6.81]
278.8 [10.98]
91.4 [3.60]
96.8 [3.81]
265.4 [10.45]
74.9 [2.95]
173.5 [6.83]
163.9 [6.45]
A
A
Port Thread size (in.) Description
P
3/4-16 UNF-2B
straight THD O-ring
Manifold block
pressure
SB-2
3/4-16 UNF-2B
straight THD O-ring
Balance piston
and inlet bear-
ings
SB-3
1 1/16-12 UN-2B
straight THD O-ring
Compressor oil
supply
SC-5
9/16-18 UNF-2B
straight THD O-ring
Inlet pressure
SC-6
9/16-18 UNF-2B
straight THD O-ring
Discharge pres-
sure
SC-7 1/8-27 NPTF Seal weepage
SC-8
1 1/16-12 UN-2B
straight THD O-ring
Closed thread
drain
SC-9
9/16-18 UNF-2B
straight THD O-ring
Inlet housing oil
drain
SC-11
1 5/16-12UN-2B
straight THD O-ring
Closed thread
drain
SC-13
9/16-18 UNF-2B
straight THD O-ring
Oil drain cylinder
SC-14
9/16-18 UNF-2B
straight THD O-ring
Liquid injection
bleed
SD-1
1 1/16-12 UN-2B
straight THD O-ring
Coalescer bleed
SE-1 1/2-14 NPTF
Electrical con-
nector
SL-1
1 1/16-12 UN-2B
straight THD O-ring
Low Vi liquid
injection
SL-2
1 1/16-12 UN-2B
straight THD O-ring
Hi Vi liquid injec-
tion
SM-1
1 5/16-12 UN-2B
straight THD O-ring
Main oil injection
SV-1 2 square ange
Vapor injection-
tongue and
groove
TE-1 3/4-14 NPTF
Suction gas tem-
perature element
T
9/16-18 UNF-2B
straight THD O-ring
Manifold block
tank
MOUNTING FOOTC
L
TRANSDUCER
MOUNTING
SPOTFACE
31.8 [ 1.25]
1.5 [.06] DP
1/4-28 UN-2B
12.7 [.50] DP
TRANSDUCER MOUNT-
ING SPOTFACE
31.8 [ 1.25]
1.5 [.06] DP
1/4-28 UN-2B
12.7 [.50] DP
SLIDE VALVE LINEAR
TRANSMITTER
SUCTION FLANGE "8" CLASS 300
ANSI FLANGE M22 X 2.5-6H 38.1
[1.50] DP
12 PL
E Q SPACED ON A 330.2 [13.00] B.C.
M24 EYEBOLT FOR LIFTING (USE 2 SHOWN
WHEN MOUNTING COMPRESSOR
635 [25.00]
DISTANCE REQUIRED FOR
STRAINER REMOVAL
INSTALL A SOLID 1/2-14 NPTF PIPE
PLUG IN THIS LOCATION WHEN USING
PORT SB-2 FOR BALANCE PISTON AND
INLET BEARING SUPPLY.
DO NOT PLUG THIS PASSAGE IF PORT
SB-2 IS NOT PIPED. BLOCKING THIS
PASSAGE WHEN PORT SB-2 IS NOT
PIPED CAN RESULT IN A CATASTROPHIC
FAILURE DUE TO LACK OF OIL SUPPLIED
TO THE BALANCE PISTON AND INLET
BEARINGS.
SECTION A-A
INLET END