Frick SGXH-4021 - Page 15

070.650-IOM (JUL 19)
Page 15
SGC/SGX ROTARY SCREW COMPRESSOR
INSTALLATION
Figure 5: Port locations, SGC 2321 (continued)
2000.6 [78.76]
608.9 [23.97]
101.9 [4.01]
468.6 [18.45]
335.3 [13.20]
255.5 [10.06]
511 [20.12]
314.2 [12.37]
243.2 [9.58]
Ă317.5 [Ă12.50]
317.5 [12.50]
578.1 [22.76]
289.1 [11.38]
1329.7 [52.35]
133.3 [5.25]
33 [1.30]
100.1 [3.94]33 [1.30]
100.1 [3.94]
MOUNTING HOLE
Ă26 [Ă1.024]
THRU
4 PL
434.3 [17.10]
340.4 [13.40]
62 [2.44]
170.2 [6.70]
59.7 [2.35]
161 [6.34]
88.9 [3.50]
186.4 [7.34]
Ø
114.3 [4.50]
106 [4.17]
177.8 [7.00]
841.2 [33.12]
8.4 [.33]
326.9 [12.87]
74.6 [2.94]
323.9 [12.75]
BEFORE DISASSEMBLY.
CAUSE INJURY DUE TO SPRING
TENSION RELEASE.
HIGH SPRING LOAD.
IMPROPER DISASSEMBLY MAY
CONSULT SERVICE MANUAL
CYLINDER ASSEMBLY UNDER
CAUTION
3. REFER TO INSTALLATION OPERATION AND
MAINTENANCE MANUAL FOR ADDITIONAL
THIS EQUIPMENT HAS BEEN PRESSURIZED
WITH NITROGEN GAS. TEMPORARY VALVES
1. RELIEVE PRESSURE PRIOR TO OPENING
LINES OR MAKING FIELD CONNECTIONS.
2. REMOVE CHARGING VALVES OR GAUGES
ESCAPING GAS MAY CAUSE INJURY
PRIOR TO PRESSURIZING SYSTEM.
INFORMATION.
CAUTION
& GAUGES HAVE BEEN INSTALLED.
SC-13
SC-9
SC-13
SC-13
SC-13
SC-11
2.500
2.499
DISCHARGE FLANGE
6" CLASS 300 ANSI FLANGE
M20x2.5-6H
31.8 [1.25] DP
12 PL
EQ SPACED ON A
Ă269.7 [Ă10.62] B.C.
SC-7
SC-8
63.50
63.47
2.146
2.139
54.51
54.33
.625
.627
15.88
15.93
[
[
[
]
]
]
SM-1
SL-1
SV-1
SLIDE STOP
LINEAR TRANSMITTER
TE-1
VIEW A-A
OUTLET END
A
A
OUTLET END
SLIDE STOP
LINEAR TRANSMITTER
VIEW A-A
MOUNTING HOLE 26 [ 1.024]
THRU 4 PL
DISCHARGE FLANGE 6 IN. CLASS
300 ANSI FLANGE M20 X 2.5-6H
31.8 [1.25] DP 12 PL EQ SPACED
ON A 269.7 [ 10.62] B.C.
787.4 [31.00]
DISTANCE REQUIRED
FOR CYLINDER
REMOVAL
177.8 [7.00] MINIMUM
DISTANCE REQUIRED
FOR SHAFT SEAL
REMOVAL
MOUNTING FOOTC
L