How to correct the picture position on my Fujitsu Monitor?
If the picture position on your Fujitsu monitor is not correct, press the AUTO button to conduct the auto-adjustment of the screen. This will help correct the alignment if the monitor recognises an undefined mode.
How to fix wrongly adjusted picture on Fujitsu B19-7 LED?
To correct a wrongly adjusted picture on your Fujitsu Monitor, run the Factory Recall function in the OSD menu. The Auto Processing message will then appear.
What to do if my Fujitsu B19-7 LED says 'No Signal'?
If your Fujitsu monitor displays a 'No Signal' message, ensure the data cable is securely connected to the monitor port on your computer and verify that the computer is powered on.
What to do if my Fujitsu Monitor has no screen display but the power indicator is lit?
If your Fujitsu monitor's power indicator is lit but there's no screen display, try the following: * Ensure that your computer is turned on. * Verify that the monitor's data cable is correctly attached to the computer's port. * Press any key on the keyboard, as the computer may be in power saving mode. * Adjust the brightness and/or contrast settings until the picture appears.
How to fix a Fujitsu B19-7 LED when the picture is shaking?
If the picture on your Fujitsu monitor is shaking, check that the data cable is correctly attached to the monitor port on the computer. If the issue persists, press the AUTO button to conduct the auto-adjustment of the screen.
What to do if my Fujitsu B19-7 LED has picture disturbances (vertical lines)?
If you are experiencing picture disturbances such as vertical lines on your Fujitsu monitor, press the AUTO button to initiate the screen's auto-adjustment feature.
What to do if my Fujitsu B19-7 LED Monitor displays 'Frequency out of range'?
If your Fujitsu monitor shows a 'Frequency out of range' message, it means the input signal doesn't match the monitor's technical specifications. Adjust the video frequency range using your computer's software, referring to your computer or display adapter's documentation. Alternatively, set a different screen resolution via your computer's software, consulting the relevant documentation.
What to do if my Fujitsu Monitor has picture disturbances (horizontal lines, picture noise)?
If your Fujitsu monitor is showing picture disturbances like horizontal lines or picture noise, try pressing the AUTO button to perform an auto-adjustment of the screen.
How to fix a Fujitsu B19-7 LED with no screen display and the power indicator does not light up?
If your Fujitsu monitor has no screen display and the power indicator is off, check that the power cable is correctly connected to the monitor and ensure that the computer is switched on.
Details critical safety precautions for device installation, operation, and handling.
Steps for unpacking the monitor and verifying package contents and condition.
Instructions for physically setting up the monitor, ensuring proper ventilation.
Guidance on positioning the monitor, keyboard, and workspace for optimal ergonomics.
Details on connecting data and power cables to the monitor itself.
Instructions for connecting the monitor to the computer and power outlet.
Explains the process of powering the monitor on and off and indicator status.
Introduces the OSD menu and button functions for adjusting monitor settings.
Details direct settings adjustment using physical buttons without the OSD menu.
Guide to navigating and modifying settings within the On-Screen Display menu.
General| 3D | No |
|---|---|
| HD type | - |
| Pixel pitch | 0.293 x 0.293 mm |
| Aspect ratio | 5:4 |
| Display surface | Matt |
| Display diagonal | 19 \ |
| Display resolution | 1280 x 1024 pixels |
| Display technology | LED |
| Vertical scan range | 56 - 76 Hz |
| Horizontal scan range | 30 - 82 kHz |
| Supported video modes | 480p |
| Contrast ratio (dynamic) | 2000000:1 |
| Contrast ratio (typical) | 1000:1 |
| Display number of colors | 16.78 million colors |
| Display brightness (typical) | 250 cd/m² |
| Supported graphics resolutions | 640 x 480 (VGA), 720 x 400, 800 x 600 (SVGA), 1280 x 1024 (SXGA) |
| Rotating | Yes |
| Active display area (W x H) | 375 x 300 mm |
| Mean time between failures (MTBF) | 70000 h |
| Cables included | AC, Audio (3.5mm), DVI, VGA |
| Tilt angle range | -5 - 35 ° |
| Cable lock slot type | Kensington |
| Number of OSD languages | 19 |
| Panel mounting interface | 100 x 100 mm |
| On Screen Display (OSD) languages | ARA, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, FIN, FRE, ITA, JPN, NOR, POL, POR, RUS, SWE, TUR |
| HDMI ports quantity | 0 |
| DVI-D ports quantity | 1 |
| Headphone connectivity | 3.5 mm |
| RMS rated power | 3 W |
| Number of speakers | 2 |
| Sustainability certificates | EPEAT Gold, ENERGY STAR |
| Certification | CE certification according to EC Directive 2004/108/EEC, EN 60950, RoHS, WEEE, IT-Eco- Declaration, EN 60601-1-2, TÜV GS, EAC, FCC Class B, cUL, VCCI, KC (planned), TÜV-S, S-Mark, BSMI (planned), CCC, SASO, ISO9241-307 (Pixel fault class I), TCO Displays 6.0 |
| Product color | Gray |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Annual energy consumption | 22 kWh |
| Power consumption (standby) | - W |
| Power consumption (typical) | 15 W |
| Power consumption (PowerSave) | 0.23 W |
| Package weight | 7200 g |
| Windows operating systems supported | Windows 10 Education, Windows 10 Education x64, Windows 10 Enterprise, Windows 10 Enterprise x64, Windows 10 Home, Windows 10 Home x64, Windows 10 Pro, Windows 10 Pro x64 |
| Operating temperature (T-T) | 5 - 35 °C |
| Harmonized System (HS) code | 85285210 |
Weight and Dimensions| Depth (with stand) | 209 mm |
|---|---|
| Height (with stand) | 370 mm |
| Weight (with stand) | 5480 g |
| Depth (without stand) | 64 mm |
| Width (without stand) | 414 mm |
| Height (without stand) | 349 mm |
| Weight (without stand) | 2850 g |
To Next Page