What to do if Furuno Marine GPS System keys are not responding?
If your Furuno Marine GPS System is not responding to key presses, try turning the power off and then on again. If the issue persists, the key may be damaged.
Why Furuno Marine GPS System position is not fixed within 90 seconds?
If your Furuno Marine GPS System fails to fix its position within 90 seconds, consider these steps: * Ensure the antenna connector is tightly secured. * Check the GPS Status Display for the number of satellites being received. * Verify that [POSITION&SOG/COG] in the [SELECT INPUT DEVICE] menu within the [INTERFACE] menu is set to [Internal GPS]. * Execute [RESTART GPS] located in the [INTERNAL GPS SETUP] menu under the [SYSTEM] menu.
What to do if no picture appears on Furuno Marine GPS System, but the power is on?
If your Furuno Marine GPS System is powered on but the screen is blank, press the POWER/BRILL key and rotate the RotoKey clockwise to increase the screen brightness.
What to do if my Furuno Plotter won't turn on?
If your Furuno Plotter won't turn on, check the following: a blown fuse, the power connector is tightly fastened, corrosion on the power cable connector, a damaged power cable, and ensure the battery voltage is 10.8 to 31.2 V.
How to improve picture sensitivity on Furuno Plotter?
If the picture sensitivity is too low on your Furuno Plotter: Check the gain setting in manual operation. Inspect the transducer for marine life or air bubbles. Consider that the bottom might be too soft to return an acceptable echo.
How to show zero line on Furuno Plotter?
If the picture appears on your Furuno Plotter but the zero line is missing: The picture might be shifted, so check the shift setting. Also, verify if [ZERO LINE REJECTION] in the [FISH FINDER] menu is turned off.
Why do marks appear but no picture on my Furuno Plotter?
If marks and characters appear on your Furuno Plotter but there's no picture, check that the transducer cable is connected.
What to do if fish finder display shows no picture on Furuno Plotter?
If you've selected the fish finder display on your Furuno Plotter but see no picture: Check that the transducer cable is fastened. Also, verify that the fish finder source is correctly selected.
How do I turn on track plotting on Furuno Plotter?
If the track of your boat is not being plotted on your Furuno Plotter, ensure that the track is turned on. Operate the [Track] soft control to turn track on.
What to do if my Furuno Plotter bearing is wrong?
If the bearing is wrong on your Furuno Plotter, check the magnetic variation setting at [COMPASS SETUP] in the [SYSTEM] menu.
General safety advice, handling instructions, and product disposal guidelines.
Essential warnings and cautions for preventing injury or equipment damage.
Detailed description of the unit's controls and buttons for operation.
Explanation of the RotoKeyTM and soft control functions and operation.
Step-by-step guide for powering the unit on and off.
Overview of the plotter's capabilities and map display features.
Guide to selecting and customizing the home screen displays.
How to navigate and operate the unit's menus.
Procedure for marking a man overboard position and related functions.
How to show, hide, and manage the boat's recorded track.
Instructions for starting, stopping, and configuring track recording parameters.
Methods for marking and saving points on the plotter display.
How to move points, select visibility, search, sort, and filter points.
Step-by-step guide to creating routes using menus and features.
How to navigate to quick points and saved points.
How to select and start navigation along a chosen route.
Understanding AIS target symbols and DSC message information.
Regular checks and cleaning procedures for optimal equipment performance.
Instructions for replacing fuses and resolving common operational issues.
Guidelines for mounting the main display unit on a tabletop or flush.
Instructions for selecting a suitable location and mounting the GPS antenna unit.
Methods for installing thru-hull, transom, and inside-hull transducers.
Guide to connecting power cables, GPS antenna, and transducers.
Performing initial system setup and configuring CAN bus data.
To Next Page
General
