Why is my Bluetooth audio cutting out on my Fusion MS-IP700i?
To prevent interruptions to audio streaming over Bluetooth on your Fusion Marine Audio system, ensure the music device is not covered or obstructed, and it is located near the Bluetooth module. It is also recommended that the Discoverable feature is turned off after pairing your device to the Fusion stereo.
Why doesn't my Fusion Marine Audio head unit recognize my MS-BT200 Bluetooth Module?
If you have installed the MS-BT200 Bluetooth module or SiriusXM Tuner (USA Only) to your Fusion Marine Audio, you will need to enable the source. This operation will be determined by the Tuner region you have selected.
How to reset Fusion Marine Audio unit when it doesn't respond?
If your Fusion Marine Audio unit does not respond to key presses, reset it by pressing the Reset button inside the control panel door.
Why does my Fusion MS-IP700i head unit freeze when connected to my iPod or iPhone?
If your Fusion head unit keeps locking up when connected to your iPod or iPhone, try the following: * Reset the head unit by pressing the reset button inside the face plate. * Reset your iPod or iPhone (refer to the Apple website for model-specific information). Also, ensure you have the latest version of iTunes and the latest operating software on your iPod or iPhone, as updating the software when Apple releases new versions is important.
What to do if my Fusion Marine Audio FUSION-Link Wireless application displays “No stereo available”?
If your Fusion-Link Wireless application displays “No stereo available”, the first thing to check is that you are connected to the correct wireless network for the 700 Series. Once you have confirmed this, close the App on the device and restart it.
Why won't my Fusion Marine Audio FUSION-Link Wireless remote application connect to my 700 Series stereo?
If your Fusion-Link Wireless remote application will not connect to your 700 Series stereo, the first thing to check is that the 700 Series is displaying a valid IP address on the about screen. Select the settings menu, then 'about' to confirm.
What to do if my Fusion MS-IP700i Marine Audio SiriusXM displays ‘No Signal’?
If you see the SiriusXM message ‘No Signal’ on your Fusion Marine Audio, ensure the antenna is not damaged and has a clear view of the sky and is not obscured. Also, ensure the antenna cable has not been damaged.
What to do if my Fusion Marine Audio SiriusXM displays ‘Check Antenna’?
If you see the SiriusXM message ‘Check Antenna’ on your Fusion Marine Audio, ensure the antenna is plugged into the SiriusXM Tuner module and is not damaged. Also, ensure the antenna cable has not been damaged.
What to do if my Fusion MS-IP700i Marine Audio SiriusXM displays ‘Check Tuner’?
If you see the SiriusXM message ‘Check Tuner’ on your Fusion Marine Audio, ensure the SiriusXM module is plugged into the MS700i and the SiriusXM cable has not been damaged.
What to do if my Apple Device goes into thermal protection with Fusion MS-IP700i?
If your Apple iPhone or iTouch shuts down due to exceeding the operating temperature, carefully remove it from the MS-IP700i Fusion Marine Audio and allow it to cool down before using it again.
Operation of the rotary encoder and menu key for navigation.
Detailed instructions on using the encoder and menu key for adjustments.
Steps to access menus and change settings using the encoder and menu key.
Instructions for turning the unit on and off.
How to adjust speaker output volume level across multiple zones.
Adjusting sub-woofer levels for each zone and tone settings for all zones.
How to select and listen to different tuner bands (AM, FM, VHF, SiriusXM).
Methods for tuning frequencies, channels, or presets (manual, auto, scan, preset).
How to connect and play content from an iPod.
How to select tracks and control playback (play, pause, skip, fast forward/rewind).
How to connect and play music from a USB flash drive.
How to control playback of audio tracks from a USB flash drive.
How to connect and listen to audio from an auxiliary device.
General| Water Resistance | IPx5 |
|---|---|
| Bluetooth | Yes |
| Radio Tuner | AM/FM |
| Display | LCD |
| iPod/iPhone Compatibility | Yes |
| USB Input | Yes |
| AUX Input | Yes |
| NMEA 2000 | Yes |
| Ethernet | No |
| Amplifier | Built-in |
| Speaker Impedance | 4-8 Ohms |
| Frequency Response | 20 Hz - 20 kHz |
| Signal-to-Noise Ratio | 80 dB |
| Current Draw | 10A |
| Operating Voltage | 12V DC |
| Protection | Overload, Short Circuit |
| Power Output | 4 x 50 Watts |
To Next Page
