FUTABA 10J - R3008 Sb Ch Mode

Beforeuse
29
R3008SBCHMODE
The R3008SB receiver is a very versatile
XQLW,WKDV3:0RXWSXWV6%86DQG6%86
outputs. Additionally the PWM outputs can be
FKDQJHGIURPFKDQQHOVWRFKDQQHOV,I
you only desire to use it as an 7 channel receiver
ZLWKRXW6%86LWFDQEHXVHGZLWKRXWDQ\
setting changes.
'DQJHU
'RQWWRXFKZLULQJ
* There is a danger of receiving an electric shock.
'RQWVKRUWFLUFXLWWKHEDWWHU\WHUPLQDOV
* A short circuit across the battery terminals may cause
DEQRUPDOKHDWLQJ¿UHDQGEXUQV
3OHDVHGRXEOHFKHFN\RXUSRODULW\
＋
DQG
−
ZKHQKRRNLQJXS\RXUFRQQHFWRUV
,I
＋
and
−
RIZLULQJDUHPLVWDNHQLWZLOOGDPDJH
ignite and explode.
'RQ¶WFRQQHFWWR([WUD9ROWDJHEHIRUH
WXUQLQJRQDUHFHLYHUSRZHUVXSSO\
+RZWRFKDQJHWKH56%&KDQQHOPRGH
The R3008SB is capable of changing its channel
allocations as described in the table below.
1. Turn on the receiver. (At this moment, the
transmitter should be off.) Then, LED blinks
RED in about 3 seconds. Next, wait until it
becomes solid RED.
2. Press and hold the Mode Switch more than
5 seconds.
3. Release the button when the LED blinks
RED and GREEN simultaneously.
4. The receiver is now in the "Operation
CH Set" mode. At this moment, the LED
LQGLFDWHVFXUUHQWVHWVWDWXVWKURXJKÁDVKLQJ
a pattern that corresponds to the CH
mode.
*Cannot exit this CH setting mode before the operation
PRGHLV¿[HG
*See the below table that shows correspondence between
&+PRGHDQGZD\RIÀDVKLQJ/('
*Default CH mode is "Mode B".
5. By pressing the Mode Switch, the operation
CH is switched sequentially as "Mode C"
"Mode D" "Mode A"....
6. The operation mode will be set by pressing
the Mode Switch more than 2 seconds at
the desired CH mode.
7. Release the button when the LED blinks
RED and GREEN simultaneously. Then, the
RSHUDWLRQ&+LVÀ[HG
8. After confirming the operation CH mode
is changed, turn off and back on the
receiver power.
*The “Operation CH Set” mode cannot be changed during
the receiver communicates to the transmitter.
Output
connector
Channel
Mode Ａ
1 〜 8CH
ModeB
1 〜 7CH
ModeC
9 〜 10CH
ModeD
9 〜 10CH
11199
2 2 2 10 10
333−−
444−−
555−−
666−−
7/B 7 7 − −
8/SB 8 S.BUS − S.BUS
RedLEDblink 1time 2time 3time 4time
R3008SB CH Mode table
Default CH mode
([WUD9ROWDJH&RQQHFWRU
Use this connector when using a voltage
telemetry device to send the battery voltage (DC0
a9IURPWKHUHFHLYHUWRWKHWUDQVPLWWHU
You will need to purchase the optional External
9ROWDJHLQSXWFDEOH&$59,1)870
You can then make a cable with an extra
connector to the External voltage connector.