FUTABA 10J - Servo Monitor ／ Servo Test

49
Commonfunction
Function
Method
①Callthemenuscreenfromthe
homescreenbypressingthe+key
for1second.
＋
② Select
fromthemenuwiththeJog
key.
③Openthesettingscreenby
pressingtheJogkey.
（1second）
Callingthesettingscreen
The servo display/servo test function displays
the CH1 to CH10 servo output bar graph and tests
servo operation.
ŏ7KHVHUYRGLVSOD\IXQFWLRQFDQEHXVHGIRUDVLPSOH
RSHUDWLRQFKHFNRIVXFKIXQFWLRQVDVWKHPL[LQJ
IXQFWLRQ
ŏ:KHQWKHVHUYRWHVWIXQFWLRQLVWXUQHGRQWKHVHUYR
PRYHVWRWKHOHIWDQGULJKWDWWKHVHWSHULRG$
YDULDEOHVSHHG/15OLQHDUPRGHRUÀ[HGVSHHG
-03MXPSPRGHFDQEHVHOHFWHG7KLVFDQEH
XVHGWRFKHFNWKHVHUYRHWF2SHUDWLRQ212))
FDQDOVREHVHOHFWHGIRUHDFKFKDQQHO
"SERVO"
SERVO
Servomonitor ／ Servotest
(Common)
(ServoMonitor）
● Selectthesettingitem
withtheJogkey.
Switchingtotheservotest
screen
● Switchthescreenbyselecting
TESTandoperatingthejog
keytotheleftandright.
● Theservooperatingposition
ofeachchannelisdisplayed
onabargraph.
(ServoTest）
ServotestON/OFF
ChannelSelect
Screenchange
● Where"GRPH"ischosen,a
Jogkeyispressed inrightor
left.
TypeSelect
CycleSelect
Speedsetting
● Operationofaservotest
■ Type/cycle/speedsetting
① Selectthesettingitem(TYPE,CYCL,
SPD)withtheJogkeyandsettheitem
bypressingthe+keyor‒key.
＋ −
or
（Range ／ Default）
TYPE：LNR,JMP ／ LNR
CYCL：1 〜 100 ／ 10（fullspeedat1）
SPD：1 〜 100 ／ 7（fullspeedat100）
■ Channelselection
② Selectthechannelyouwantto
testwiththeJogkeyandselect
ACT/INHbypressingthe+key
or‒key.
＋ −
or
Selectionrange：ACT,INH
Default：INH（onlyCH1isACT）
■ Servoteststart/stop
③Selectthe"TEST"item
withtheJogkeyand
start/stoptheservotest
bypressingthe+keyor‒
key.
＋ −
or
Selectionrange：ON,OFF
Default：OFF
Servotest

Using the servo test will move the servos to
their full throw. Do not use this with linkages
installed. Using it may damage the servo and
linkage.
6(592岜岜 7(67㌣

6(592岜岜 *53+㌣
ٕ
ٹ$&7ٸ,1+
ٹٸٸٸٸٸٸٸ
7<3(㌣/15
&<&/㌣
63'㌣
&+㌣
7(67㌣2))
CAUTION