3.1.3 Verify the Main CPU is Operating ...................................................................................... 3-1
3.2 Start-Up Procedures................................................................................................................... 3-2
3.2.1 Requirements for a running platform during initial startup ................................................. 3-2
3.2.2 Complete the Installation of Equipment ............................................................................. 3-4
3.3 Adjustment Procedures .............................................................................................................. 3-5
3.3.1 Set Toggle Switches ........................................................................................................... 3-5
3.3.2 Ready the Car to Run on Inspection .................................................................................. 3-5
3.3.3 Prepare for the Car for Hoistway Learn ............................................................................. 3-6
3.3.4 Verify the Hoistway ............................................................................................................. 3-7
3.4 Adjust the Elevator ..................................................................................................................... 3-7
3.4.1 Automatic Run .................................................................................................................... 3-7
3.4.2 Adjust the Slowdown Distances ......................................................................................... 3-8
3.4.3 Adjust the Stop ................................................................................................................... 3-9
3.4.4 Verify Proper Operation of All Safety Circuits and Signal Devices .................................. 3-10
3.4.5 Perform Required Tests ................................................................................................... 3-10
Section 4 Troubleshooting ................................................................................................................... 4-1
4.1 General Information.................................................................................................................... 4-1
4.2 Microprocessor CPU .................................................................................................................. 4-1
4.3 Input/Output Boards ................................................................................................................... 4-1
4.4 Run Sequence ............................................................................................................................ 4-2
4.5 The Safety PAL Functions ......................................................................................................... 4-3
4.6 Safety PAL ................................................................................................................................. 4-5
4.7 System Faults ............................................................................................................................. 4-6
4.8 Main CPU Inputs and outputs .................................................................................................... 4-6
4.9 NTS Processor Inputs and Outputs ......................................................................................... 4-11
4.10 Relocate I/Os ............................................................................................................................ 4-12
4.10.1 Relocate I/Os – Add IO Relocation .................................................................................. 4-13
4.10.2 Relocate I/Os – Remove Relocation IO ........................................................................... 4-14
4.10.3 Car Trace Screen ............................................................................................................. 4-15
Section 5 LCD Interface ........................................................................................................................ 5-1
5.1 Operating the LDC Interface ...................................................................................................... 5-1
5.2 LCD Menus ................................................................................................................................ 5-2
5.2.1 Elevator Status ................................................................................................................... 5-2
5.2.2 Main Menu ........................................................................................................................ 5-12
5.2.3 Date and Time .................................................................................................................. 5-13
5.2.4 Set Calls and Lockouts ..................................................................................................... 5-14
5.2.5 Inputs and Outputs ........................................................................................................... 5-17
5.2.6 Job Statistics .................................................................................................................... 5-20
5.2.7 Adjustable Variables ......................................................................................................... 5-21
5.2.8 Diagnostics ....................................................................................................................... 5-22
5.2.9 Software Utilities ............................................................................................................... 5-29
5.2.10 Hoistway Tables ............................................................................................................... 5-33
5.2.11 Fault Log........................................................................................................................... 5-39
Section 6 - Main CPU Faults & Detailed Faults ................................................................................ 6-40
6.1 Main CPU Faults ...................................................................................................................... 6-40
6.2 Device Fault in Fault Log ......................................................................................................... 6-84
6.3 Detailed Faults Data and Description....................................................................................... 6-99
6.3.1 Detailed Fault I/O Data Example .................................................................................... 6-112
6.3.2 Detailed Fault I/O Data Form ......................................................................................... 6-115
Section 7 - Main CPU Adjustable Variables ........................................................................................ 7-1
Section 8 - Appendix A ......................................................................................................................... 8-1
8.1 Testing Stall Mode & Low Oil Operation .................................................................................... 8-1
8.2 Reset Low Oil, Hot Oil, or MC/SPD Fault................................................................................... 8-2
8.3 Performing a Stop Ring Test ...................................................................................................... 8-2
To Next Page
Loading...