GE D60 - Page 821

GE Multilin D60 Line Distance Protection System vii
INDEX
O
ONE SHOTS.................................................................. 5-155
OPEN POLE DETECTOR
FlexLogic operands ..................................................... 5-148
logic..................................................................5-313, 5-314
Modbus registers ........................................................... B-43
settings ....................................................................... 5-311
specifications ................................................................ 2-22
OPERATING TEMPERATURE .......................................... 2-28
OPERATING TIMES......................................................... 2-17
ORDER CODES....................... 2-8, 2-10, 2-11, 2-13, 6-29, 7-3
ORDER CODES, UPDATING.............................................. 7-3
ORDERING ............................................. 2-8, 2-10, 2-11, 2-13
OSCILLATORY TRANSIENT TESTING ............................. 2-29
OSCILLOGRAPHY
actual values ................................................................. 6-27
clearing.................................................................. 5-26, 7-2
Modbus ...........................................................................B-7
Modbus registers .................................................. B-21, B-32
settings ......................................................................... 5-71
specifications ................................................................ 2-23
via COMTRADE...............................................................B-7
via EnerVista software ..................................................... 4-2
OST ......................................................................2-21, 5-191
OUT-OF-STEP TRIPPING ......................................2-21, 5-191
OUTPUTS
contact outputs............................................................ 5-349
control power ................................................................ 2-26
critical failure relay ........................................................ 2-26
Fast Form-C relay ......................................................... 2-26
Form-A relay ................................................ 2-26, 3-12, 3-13
Form-C relay .........................................................2-26, 3-12
latching outputs ...................................................2-26, 5-349
remote outputs ..................................................5-354, 5-355
virtual outputs ............................................................. 5-351
OVERCURRENT CURVE TYPES.................................... 5-201
OVERCURRENT CURVES
definite time ................................................................ 5-205
FlexCurves.................................................................. 5-205
I2T .............................................................................. 5-205
IAC ............................................................................. 5-204
IEC ............................................................................. 5-203
IEEE ........................................................................... 5-201
OVERFREQUENCY
FlexLogic operands ..................................................... 5-148
logic............................................................................ 5-272
settings ....................................................................... 5-272
specifications ................................................................ 2-20
OVERFRQUENCY
Modbus registers ........................................................... B-41
OVERVOLTAGE
auxiliary ..............................................................2-20, 5-248
compensated............................................................... 5-249
negative sequence ...................................................... 5-246
negative-sequence ........................................................ 2-20
neutral ................................................................2-20, 5-245
phase..................................................................2-20, 5-244
P
PANEL CUTOUT......................................................... 3-1, 3-2
PARALLEL REDUNDANCY PROTOCOL
actual values .................................................................6-11
explained.......................................................................5-31
settings .........................................................................5-30
specifications.................................................................2-27
PARITY............................................................................5-27
PASSWORD SECURITY
FlexLogic operands ...................................................... 5-153
PASSWORDS
changing .......................................................................4-30
for settings templates.......................................................4-6
lost password ..................................................................5-8
Modbus registers ................................................. B-19, B-29
overview ........................................................................1-19
reset to factory defaults....................................................5-8
security ...........................................................................2-4
settings ...........................................................................2-3
PC SOFTWARE
see entry for ENERVISTA UR SETUP
PERMISSIVE FUNCTIONS ............................................. 5-241
PERMISSIVE OVERREACH TRANSFER TRIP
see entry for POTT
PERMISSIVE UNDERREACH TRANSFER TRIP
see entry for PUTT
PER-UNIT QUANTITY ........................................................5-4
PHASE ANGLE METERING .............................................. 6-14
PHASE CURRENT METERING .........................................6-16
PHASE DIRECTIONAL OC
Modbus registers .......................................................... B-48
PHASE DIRECTIONAL OVERCURRENT
FlexLogic operands ...................................................... 5-148
logic ............................................................................ 5-211
phase A polarization .................................................... 5-209
settings ............................................................ 5-209, 5-210
specifications.................................................................2-19
PHASE DISTANCE
application of settings ......................................................9-2
FlexLogic operands ...................................................... 5-148
logic ............................................................................ 5-180
Modbus registers .......................................................... B-46
op scheme ................................................................... 5-179
settings ....................................................................... 5-171
specifications.................................................................2-17
PHASE INSTANTANEOUS OVERCURRENT
see entry for PHASE IOC
PHASE IOC
FlexLogic operands ...................................................... 5-149
logic ............................................................................ 5-208
specifications.................................................................2-19
PHASE MEASUREMENT UNIT
see entry for SYNCHROPHASOR
PHASE OVERVOLTAGE
FlexLogic operands ...................................................... 5-149
logic ............................................................................ 5-244
Modbus registers .......................................................... B-46
settings ....................................................................... 5-244
specifications.................................................................2-20
PHASE ROTATION ........................................................ 5-101
PHASE SELECT
FlexLogic operands ...................................................... 5-149
PHASE TIME OVERCURRENT
see entry for PHASE TOC
PHASE TOC
FlexLogic operands ...................................................... 5-149
logic ............................................................................ 5-207
settings ....................................................................... 5-206
specifications.................................................................2-18