GE G30 - Page 678

698 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

F-12 G30 Generator Protection System GE Multilin

F.2 DNP POINT LISTS APPENDIX F

F

Table of Contents

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
  - Cautions and Warnings11
  - Inspection Procedure12
- Ur Overview13
- Enervista Ur Setup Software15
- Ur Hardware26
- Using the Relay27
2 Product Description31
- Introduction31
- Order Codes40
- Signal Processing47
  - Ur Signal Processing47
- Specifications49
3 Hardware63
- Description63
  - Panel Cutout63
  - Rear Terminal Layout69
- Wiring71
- Direct Input/Output Communications95
4 Human Interfaces113
- Enervista Ur Setup Software Interface113
- Extended Enervista Ur Setup Features116
- Faceplate Interface125
5 Settings139
- Overview141
- Product Setup148
- System Setup240
- Flexlogic268
- Grouped Elements291
- Control Elements354
- Inputs and Outputs386
- Transducer Inputs and Outputs405
- Testing411
6 Actual Values415
- Overview415
  - Actual Values Menu415
- Status415
- Records440
- Product Information442
  - Model Information442
  - Firmware Revisions442
7 Commands and443
- Commands443
8 Theory of Operation455
- Directional Principle455
  - Current Directional Protection455
9 Application of Settings457
- Setting Example457
10 Commissioning471
- Testing471
  - Testing Underfrequency and Overfrequency Elements471
11 Maintenance473
- Modules473
  - Replace a Module473
- Batteries475
  - Replace Battery475
  - Dispose of Battery477
- Uninstall and Clear Files and Data480
- Repairs481
- Storage482
- Disposal483
Parameter Lists485
- Flexanalog Items485
- A.1.1 Flexanalog Items485
- Flexinteger Items511
- A.1.2 Flexinteger Items511
Modbus Rtu Protocol513
- Introduction513
- Physical Layer513
- Data Link Layer513
- B.1.2 Physical Layer513
- Modbus Rtu Crc-16 Algorithm514
Modbus Function Codes516
- Supported Function Codes516
- Read Actual Values or Settings (Function Code 03/04H516
- Execute Operation (Function Code 05H517
- Store Single Setting (Function Code 06H517
- Store Multiple Settings (Function Code 10H518
- Exception Responses518
- B.3.1 Obtaining Relay Files Via Modbus519
File Transfers520
Memory Mapping521
- Modbus Memory Map521
- Data Formats585
- B.4.2 Data Formats585
Iec 61850621
Overview621
- Introduction621
- Communication Profiles621
- C.1.2 Communication Profiles621
- File Transfer by Iec 61850622
Server Data Organization623
- Overview623
- Ggio1: Digital Status Values623
- Ggio2: Digital Control Values623
- Ggio3: Digital Status and Analog Values from Goose Data623
- Ggio4: Generic Analog Measured Values623
- C.2.1 Overview623
- Mmxu: Analog Measured Values624
- Protection and Other Logical Nodes624
Server Features and Configuration626
- Buffered/Unbuffered Reporting626
- File Transfer626
- Timestamps and Scanning626
- Logical Device Name626
- Location626
- Logical Node Name Prefixes627
- Connection Timing627
- Non-Iec 61850 Data627
- Communication Software Utilities627
Generic Substation Event Services: Gsse and Goose628
- Overview628
- Gsse Configuration628
- Fixed Goose628
- Configurable Goose628
- C.4.1 Overview628
- Ethernet Mac Address for Gsse/Goose631
- Gsse ID and Goose ID Settings631
Iec 61850 Implementation Via Enervista Ur Setup632
- Overview632
- C.5.1 Overview632
- Configuring Iec 61850 Settings633
- About ICD Files634
- Creating an ICD File with Enervista Ur Setup638
- About Scd Files638
- Importing an Scd File with Enervista Ur Setup641
Acsi Conformance643
- Acsi Basic Conformance Statement643
- Acsi Models Conformance Statement643
- Acsi Services Conformance Statement644
- Logical Nodes Table647
Iec 60870-5-103651
- Overview651
- Factor and Offset Calculation to Transmit Measurand651
- D.1.1 Overview651
- Interoperability Document652
- D.1.3 Interoperability Document652
Iec 60870-5-104657
- Interoperability Document657
- E.1.1 Interoperability Document657
- Iec 60870-5-104 Point List665
Device Profile Document667
- Dnp V3.00 Device Profile667
- F.1.2 Implementation Table670
Dnp Point Lists674
- Binary Input Points674
- Binary and Control Relay Output675
- Counters676
- F.2.3 Counters676
- Analog Inputs677
- F.2.4 Analog Inputs677
Radius Server Configuration679
Change Notes681
- Revision History681
- Changes to the G30 Manual681
- H.1.1 Revision History681
Abbreviations685
- Standard Abbreviations685
- H.2.1 Standard Abbreviations685
Warranty688
- Ge Multilin Warranty688
- H.3.1 Ge Multilin Warranty688

Related product manuals

Preview: GE T60

Preview: GE 345

Preview: GE 369

Preview: GE 469

Preview: GE 489

Preview: GE 750

Preview: GE Multilin 469

GE Multilin 469

Preview: GE Multilin 489

GE Multilin 489