To Next Page

To Previous Page

Page 31

LOC PG DESCRIPTION DEFAULT PROGRAMMING DATA

27 19 ZONES 9-16, ZONE TYPES 6-6-6-6-6-6-6-6 __ __ __ __ __ __ __ __

ZONES 9-16, PARTITION SELECTION (Segment 1=Zone 9 thru Segment 8=Zone 16) 28 19

Segment #1

1 - Partition #1 “

2 - Partition #2 “

Segment # 2

1 - Partition #1 ‘

2 - Partition #2 ‘

Segment #3

1 - Partition #1 “

2 - Partition #2 “

Segment #4

1 - Partition #1 “

2 - Partition #2 “

Segment #5

1 - Partition #1 “

2 - Partition #2 “

Segment #6

1 - Partition #1 “

2 - Partition #2 “

Segment #7

1 - Partition #1 “

2 - Partition #2 “

Segment #8

1 - Partition #1 “

2 - Partition #2 “

SIREN AND SYSTEM SUPERVISION

Segment #1

1 -

2 -

3 -

4 -

5 -

6 -

7 -

8 -

Siren sounds for telephone line cut while armed “

Siren sounds for telephone line cut while disarmed “

Siren blast at arming “

Siren blast at exit delay expiration “

Siren blast at closing kissoff “

Siren sounds during a cross zone verification time “

Siren sounds for a tamper “

Siren blast one time for keyswitch arming, two times for disarming “

(NOTE: This feature must be disabled for SIA

CP-01 installations.)

Segment #2

1 -

2 -

3 -

4 -

5 -

6 -

7 -

8 -

Convert siren driver to voltage out “

Siren sounds for expander trouble (required for U.L.) “

Immediate restore by zone “

Dynamic battery test performed upon arming “

Battery missing test performed every 12 seconds “

Manual bell test performed during [r]-[4] test function “

Manual communicator test performed during [r]-[4] test function “

Box tamper enabled. “

Segment #3

1 -

2 -

3 -

4 -

5 -

6 -

7 -

8 -

Box Tamper report enabled “

AC Fail report enabled “

Low Battery report enabled “

Auxiliary power over current report enabled “

Siren supervision report enabled “

Telephone Line Cut report enabled “

Reserved.

Expander trouble report enabled “

Segment #4

1 -

2 -

3 -

4 -

5 -

6 -

7 -

8 -

Failure To Communicate report enabled “

Log Full report enabled “

Autotest report enabled “

Start and End Programming report enabled “

End Download report enabled “

Sensor Low Battery report enabled “

Sensor Missing report enabled “

Reserved.

Segment #5

37 19

1 -

2 -

3 -

4 -

5 -

6 -

7 -

8 -

Lost Clock service LED enable “

Enables Zone Doubling for zones 7-12 (requires NX-200 Zone Doubling Kit) “

Disables on-board zones “

Enables two trips on the same cross-zone to activate the alarm “

Disables bypass reports for force armed zones “

Reserved

Clock uses internal crystal “

Disable Temporal Siren on Fire (must NOT disable for UL systems) “

38 20

SWINGER SHUTDOWN COUNT

1 _

Questions and Answers:

Need help?

Do you have a question about the GE NetworX NX-6 and is the answer not in the manual?

GE NetworX NX-6 Specifications

Operating Power

operating power	16.5 VAC 25, 40, or 50 VA Transformer
auxiliary power with 25 VA transformer	12 VDC Regulated 500 mA
auxiliary power with 40 or 50 VA transformer	12 VDC Regulated 1 AMP

Loop Specifications

loop resistance for standard loop	300 Ohms Maximum
loop resistance for 2-wire smokes	30 Ohms Maximum
loop response	500mS

Operating Environment

operating temperature	32 to 120 degrees F

LED Keypad Specifications

led keypad current draw	130 mA max.
led keypad dimensions width	6.4"
led keypad dimensions height	4.0"
led keypad dimensions depth	1.1"

NX-148E LCD Keypad Specifications

nx-148e lcd keypad current draw	110 mA max.
nx-148e lcd keypad dimensions width	6.4"
nx-148e lcd keypad dimensions height	5.3"
nx-148e lcd keypad dimensions depth	1.0"

Enclosure and Shipping