EasyManua.ls Logo

Gehl 1448 Plus - User Manual

Gehl 1448 Plus
84 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1448 Plus
Asphalt Paver
Beginning with Serial Number 18101
®
Form No.
918215
OPERATOR’S MANUAL
Revision C
04/07
Courtesy of Machine.Market

Table of Contents

Questions and Answers

  • R
    Rodney PorterAug 13, 2025
    What to do if Gehl 1448 Plus Construction Equipment engine will not turn over?
    • A
      Alexis SinghAug 13, 2025
      If the engine won't turn over, the issue might stem from several causes. First, check the fuse in the control module and replace it if it's blown. Another potential cause is a faulty relay, which would also need replacement. Look into the circuit breaker and reset it if it has tripped. The starter motor itself could be defective, requiring repair or replacement. Finally, inspect the wiring connections for any faults and repair them as necessary.
  • E
    ehenryAug 17, 2025
    Why is my Gehl Construction Equipment engine running rough?
    • R
      Robert ReedAug 17, 2025
      A rough-running engine may be due to a clogged fuel filter, which requires cleaning or replacement. Another potential cause is air trapped in the fuel system. Additionally, a clogged air cleaner could be the culprit, so clean or replace it.
  • J
    John SmithAug 20, 2025
    What to do if Gehl Construction Equipment engine overheats?
    • S
      Sheena SinghAug 20, 2025
      If your engine is overheating, start by checking the radiator coolant level and add coolant if it's low. Also, inspect the radiator for any clogs and clean it if necessary. Ensure the crankcase oil level is adequate, adding oil if needed. Finally, check for any restrictions in the exhaust system; after the engine cools, remove any blockage.
  • A
    Alexander WarrenAug 25, 2025
    What to do if Gehl 1448 Plus Construction Equipment engine cranks but will not start?
    • R
      Rachel JonesAug 25, 2025
      If the engine cranks but refuses to start, the fuel tank might be empty, so add fuel. Also, if the engine crankcase oil is too heavy, drain and replace it with oil of the proper viscosity. In cold conditions, preheat the engine before attempting to start it.
  • B
    Bryan EvansAug 28, 2025
    Why does Gehl Construction Equipment engine cut out abruptly?
    • J
      Jeffrey HayesAug 28, 2025
      An abrupt engine cutout can occur if the fuel tank is empty, so add fuel. Another cause is a clogged fuel filter, which should be cleaned or replaced.
  • R
    Ronald ScottSep 1, 2025
    Why Gehl Construction Equipment starter motor does not have enough power to turn the engine over?
    • J
      jamesbarnesSep 1, 2025
      If the starter motor lacks the power to turn the engine over, the battery may be defective, so charge it. Alternatively, the starter motor itself could be defective, requiring repair or replacement. Also, check the wiring connections for breaks or looseness; repair, replace, and tighten them as needed.
  • C
    Charlotte MillerSep 4, 2025
    Why is my Gehl Construction Equipment paver difficult to steer?
    • C
      crystalsmithSep 4, 2025
      Difficulty steering your paver may arise from several factors: Ensure that each forward/reverse lever is fully engaged. Check the linkage for dual controls for any binding and free it up. It is also important to verify the tracks are properly aligned and align them if necessary.
  • H
    Heather SmithSep 8, 2025
    Why is my Gehl 1448 Plus paver slowing down or losing power?
    • J
      Jessica CamposSep 8, 2025
      If your paver is slowing down or experiencing excessive power loss, first check the fuel filter. Another possible cause is failure of hydraulic system components.

Summary

Introduction

Model;Serial Number Information

Record machine model and serial numbers for reference.

Paver Controls;Components Identification

Visual guide to locate and identify paver controls and components.

Specifications

Dimensions, Measures and Weights

Details physical size, weight, and key measurements of the paver.

Engine Specifications

Provides technical data for the paver's engine, including model and performance.

Screed Specifications

Lists technical details related to the paver's screed, including width and extensions.

Drive Configuration

Describes the paver's drive system, tracks, and steering capabilities.

Hydraulic System Specifications

Outlines parameters for the paver's hydraulic system, including flow and pressure.

Performance and Service Capacities

Covers operational performance metrics and fluid/component capacities.

Checklists

Pre-Delivery Checklists

Guides for inspecting the paver before customer delivery.

Delivery Checklists

Procedures for delivering the paver and its manual to the customer.

Safety

Mandatory Safety Shutdown Procedure

Step-by-step process for safely shutting down the paver.

General Safety Reminders

Important safety practices for operation, pre-operation, and service.

Machine Safety Features

Information on guards, shields, and replacement parts for safe operation.

Safety Decals

Locations and identification of important safety decals on the paver.

Indicators and Controls

Ignition Keyswitch and Circuit Breaker

Explains the function of the ignition switch and electrical protection.

Engine Monitoring and Controls

Details instrument module indicators and engine throttle operation.

Operation Controls

Describes controls for paver movement, hopper, and screed functions.

Screed Adjustments and Heater

Covers adjustments for screed depth, crown, and the optional propane heater.

Maintenance

Maintenance Interval Chart

Lists recommended service intervals for various maintenance tasks.

Maintenance Log

Provides space to record performed maintenance services and dates.

Operation

Starting and Basic Operation

Covers engine start-up, break-in, and stopping procedures.

Paving Procedures

Guides for preparing the site, filling the hopper, and laying asphalt.

Transporting the Paver

Instructions for moving the paver on roads, between sites, and loading/unloading.

Service and Storage

General Information and Dealer Services

Outlines service responsibilities and procedures.

Operator Services and Daily Checks

Details routine checks and services performed by the operator.

Periodic Maintenance Schedules

Lists maintenance tasks for 50, 250, 500, and 1000-hour intervals.

Storage Procedures

Steps for preparing the paver for long-term storage.

Troubleshooting

Engine and General Operation Issues

Addresses problems related to the engine and overall paver operation.

Mat and Paving Problems

Guides for diagnosing issues with the asphalt mat quality.

Hydraulic System Troubleshooting

Covers problems with control valves, pumps, motors, and cylinders.

Electrical System Troubleshooting

Details common issues and solutions for the paver's electrical system.

Decal Locations

General Information and Paint Notice

Provides context for decals and lists paint codes for refinishing.

New Decal Application

Instructions on how to properly apply replacement decals.

Torque Specifications

Gehl 1448 Plus Specifications

General IconGeneral
BrandGehl
Model1448 Plus
CategoryConstruction Equipment
LanguageEnglish

Related product manuals