Gehl Z17 GEN:2 - 4. Operation License; Comply with all applicable laws.

208 pages

To Next Page

To Previous Page

0-5

4. Operation License

Before you operate this machine, confirm the licensing requirements that are applicable to the operation

of this machine.

Comply with all applicable laws.

Ask your dealer about licensing requirements.

Courtesy of Machine.Market

Main Page

Introduction3
Safety Information4
Product Overview5
- Intended Uses5
- Break in Period5
- Conditions to Insure Compliance with EPA Emission Standards6
Operation License7
Ordering Replacement Parts and Service Calls8
- Location of Machine Serial Number Plate8
- Location of Engine Serial Number Plate8
- Location of EPA Emission Control Plates8
- Ordering Replacement Parts and Service Calls9
- Table of Contents10
Safety13
Basic Precautions14
Operating Precautions18
- Precautions before Starting the Engine18
- Precautions for Starting the Engine, Working and Parking20
- Precautions for Transportation25
- Precautions for the Battery26
- Precautions for Towing27
Precautions for Servicing29
- Precautions before Servicing29
- Precautions During Servicing31
Safety Messages (Warning Labels)35
- Location of Warning Labels35
Contents37
Operation41
Identification of Important Parts42
- Overview of the Machine42
- Controls and Switches43
Description of Control Devices44
- Monitor44
- Switches47
- Control Levers and Pedals49
- Engine Hood54
- Storage Space for the Operation & Maintenance Manual54
- Operator's Seat55
- Fuse56
Operating Instructions58
- Checking before Starting the Engine58
- Starting up the Engine68
- Operating and Checking Instructions after Starting the Engine71
- Traveling73
- Steering77
- Stopping the Machine79
- Swinging the Upper Structure80
- Operating the Implement81
- Operating the Track Gauge Change82
- Precautions for Operating the Implement84
- Precautions for Working87
- Precautions for Going up and down a Slope88
- Escaping from the Mud90
- Operations Using the Bucket91
- Reversing the Bucket92
- Parking the Machine94
- Inspection Requirements after Completing Operation95
- Stopping the Engine96
- Inspection Requirements after Stopping the Engine97
- Locking97
- Handling the Rubber Crawlers98
- Handling Hydraulic P.T.O103
Transportation108
- Loading and Unloading the Machine108
- Precautions for Loading the Machine110
- Precautions for Transporting the Machine111
- Suspending the Machine112
Care and Service in Cold Weather114
- Preparing for Cold Weather114
- Precautions after a Day's Work116
- After Cold Weather Ends116
Long-Term Storage117
- Before Storing117
- Storing118
- Using the Machine Again118
Troubleshooting119
- Phenomena that Do Not Constitute Faults119
- Towing120
- If the Battery Is Overdischarged121
- Troubleshooting122
Maintenance129
Precautions for Servicing130
Basic Servicing Practices133
- Oils, Fuel, and Cooling Water134
- Electrical Equipment137
- Hydraulic System138
Consumables139
Fueling, Oiling and Greasing Based on Temperature Range140
- Fuel and Oil140
- Cooling Water140
Standard Tightening Torque for Bolts and Nuts141
- Required Tools141
- Torque Table142
Replacing Essential Parts Periodically143
Maintenance Table145
- Table of Service Time Intervals145
- Service Intervals When Using the Hydraulic Breaker149
Procedures for Maintenance150
- First Services150
- Non-Periodic Services151
- Checking before Start-Up163
- Maintenance Every 50 Service Hours171
- Maintenance Every 100 Service Hours173
- Maintenance Every 200 Service Hours174
- Maintenance Every 250 Service Hours179
- Maintenance Every 400 Service Hours180
- Maintenance Every 500 Service Hours183
- Maintenance Every 1000 Service Hours184
- Maintenance Every 2000 Service Hours187
Specifications and Dimensional Diagrams189
Optional Parts and Attachments193
General Precautions194
- Safety Precautions194
- Precautions for Mounting an Attachment (Implement)195
Maintenance Log198
Notes202

Gehl Z17 GEN:2 - 4. Operation License; Comply with all applicable laws.

Table of Contents

Related product manuals