Menu Tree
B-2
CG-1220 DTR
MAIN
MENU
APPENDIX B
-------------
DIGITAL TRACKING RECEIVER
MENU TREE
2. INPUT ATTEN
1. FREQUENCY
5. CONFIGS
FREQUENCY = 949.00 MHz (Range: 945.000 to 2055.000)
1. SPECTRAL DISPLAY
2. SPU SERIAL LINK STATS
3. I/O STATUS
4. FIFO STATUS
5. MESSAGE LOG
6. DISPLAY VERSION
7. CPU TASKS
8. TROUBLE SHOOT
7. TESTS
0. 16 KHz 2. 125 KHz 4. 32 KHz
1. 62.5 KHz 3. 250 KHz
4. STATUS
1. FILTERS
2. RECEIVER OPERATION
2. ANALOG OUTPUTS
1. LCD DISPLAY 2. LEDS TEST 3. FIFO TEST 4. FACTORY BURN IN
3. UPDATE RATE
5. SYSTEM MEMORY
2. SET DATE AND TIME
6. ACKNOWLEDGE
FAULTS
1. SET DATE
2. SET TIME
0-30 dB (2 dB steps)
3. FFT SAMPLE/AVERAGING
AVERAGING RANGE: 1 TO 2000
4. BEACON SETUP
(NOT AVAILABLE IN
MONOPULSE UNITS)
1. STORE BEACONS (1 - 4)
2. RESTORE BEACONS (1- 4)
1. COMM PARAMETERS
1. REMOTE CONTROL
BPS (BAUD)
NEWLINE
ECHO
SHELL
RESET PORT
2. PORT 1 (RS-232 ONLY)
3. PORT 2 (RS-232/RS-422)
0. I/O INTF #1 1. PORT 1 2. PORT 2 3.PORT 3
3. CONVERSION BANDS
(ONLY AVAILABLE WITH
OPTIONAL BDCs)
BAND 1 BAND 3
BAND 2 BAND 4
BDC GAIN HIGH FREQ LBAND DEFAULTS
OSC FREQ LOW FREQ (BAND 1 ONLY)
3. RESTORE ROM DEFAULTS
4. FORCE CLEAR FAULTS
6. INTERFACE OPTIONS 1. LCD CONTRAST 2. LOW SIGNAL LEVEL 3. LOW SIGNAL ALARM 4. HIGH TEMP-LIMIT
3. POL SELECT
1. 1 or 2 (DEPENDING ON
2. 1 - 6 SETTING IN POL
INPUTS)
4. PORT 3 (RS-485)
1. SAMPLING FREQUENCY
2. NCO OFFSET RANGE: -6000.000 TO 99999.999
RANGE: 63990.000 TO 64010.00
3. POWER LEVEL CALIBRATION
4. MANUAL IF OVERRIDE
1. FREQ #1 IF OVERRIDE
2. FREQ #2 IF OVERRIDE
3. FREQ #3 IF OVERRIDE
4. FREQ #4 IF OVERRIDE
1. DAC1 SETUP
1. VOLTAGE RANGE
2. MIN REF POWER LVL
3. SLOPE
4. OUTPUT
2. DAC2 SETUP
1. FACTORY CALIBRATION
5. HARDWARE OPTIONS
BPS (BAUD)
SHELL
MASTER ADDRESS
SLAVE ADDRESS
ADDRESS OFFSET
RESET PORT
POL INPUTS
0 - STANDARD
1- 6 PORTS
4. DETECTION (WIDEBAND
OPTION ONLY)
4. ATTENUATION
WIDEBAND OPTIONS
0. 16 KHz 6. 1 MHz
1. 32 KHz 7. 2 MHz
2. 62.5 KHz 8. 4 MHz
3. 125 KHz 9. 8 MHz
4. 250 KHz 10. 12 MHz
5. 500 KHz 11. 16 MHz
OR
3. MONOPULSE
(ONLY AVAILABLE IN
MONPULSE UNITS)
3. RATE (-1 to 10000)
1. MUTE (0-Disabled; 1-Enabled)
2. MUTE-FAULT (0-Dis.; 1-En.)
4. MODE (0-Vectors; 1-Levels)
5. START
To Next Page
Loading...