Index
0020200954_00 SUSTAIN ..c Installation and maintenance instructions 47
Index
A
Air index setting................................................................... 20
Air/flue pipe ......................................................................... 13
Air/flue pipe, installed ............................................................ 5
Article number ....................................................................... 8
Automatic air vent................................................................ 19
B
Burner anti-cycling time....................................................... 21
Bypass valve ....................................................................... 22
C
Carrying out
Gas family check ........................................................... 17
CE label................................................................................. 8
Check programmes....................................................... 17, 28
Checking the burner ............................................................ 24
Checking the CO₂ content ................................................... 20
Checking the pre-charge pressure of the expansion
vessel .................................................................................. 24
Cleaning the condensate siphon ......................................... 24
Cleaning the heat exchanger .............................................. 23
Combustion air ...................................................................... 5
Completing inspection work ................................................ 24
Completing maintenance work ............................................ 24
Completing repair work ....................................................... 27
Completing, repair work ...................................................... 27
Condensate drain pipework................................................. 13
Condensate siphon
Filling ............................................................................. 19
Controller............................................................................. 16
Corrosion............................................................................... 5
D
Decommissioning................................................................ 27
Decommissioning the product ............................................. 27
Diagnostics codes ............................................................... 16
Documents ............................................................................ 8
Draining the product ............................................................ 24
E
Electricity ............................................................................... 5
Expansion relief valve ......................................................... 27
F
Fault codes.......................................................................... 24
Fault memory ...................................................................... 25
Filling the heating installation .............................................. 19
Flow sensor ......................................................................... 27
Flue gas route ....................................................................... 5
Front casing, closed .............................................................. 5
Frost ...................................................................................... 6
G
Gas family check
Carrying out ................................................................... 17
H
Handing over to the operator............................................... 22
High-efficiency pump........................................................... 21
High-efficiency pump output................................................ 21
I
Identification plate ................................................................. 8
If you smell gas ..................................................................... 4
Inspection work ............................................................. 22, 37
Installation site....................................................................... 5
Installing the front casing..................................................... 11
Installing the side section .................................................... 11
Intended use.......................................................................... 4
M
Mains connection ................................................................ 15
Maintenance work ......................................................... 22, 37
Minimum clearance ............................................................. 10
P
Power supply....................................................................... 15
Preparing the repair work .................................................... 25
Preparing, repair work ......................................................... 25
Pressure sensor .................................................................. 27
Purging the heating installation ........................................... 19
Purging the product ............................................................. 19
Purging, heating installation ................................................ 19
Purging, product .................................................................. 19
R
Regulations ........................................................................... 6
Removing the air intake pipe............................................... 22
Removing the burner........................................................... 22
Removing the flue pipe........................................................ 22
Removing the gas-air mixture unit....................................... 22
Removing the side section .................................................. 11
Replacing the burner ........................................................... 25
Replacing the expansion vessel.......................................... 26
Replacing the heat exchanger............................................. 25
Replacing the main PCB ..................................................... 26
Replacing the PCB for the user interface............................ 26
Replacing, expansion vessel............................................... 26
Resetting the burner anti-cycling time ................................. 21
S
Safety device......................................................................... 5
Schematic drawing ................................................................ 5
Serial number ........................................................................ 8
Setting the burner anti-cycling time ..................................... 21
Setting the CO₂ content....................................................... 20
Spare parts.......................................................................... 22
Supply of combustion air ....................................................... 5
Switching on the product ..................................................... 19
T
Tool ....................................................................................... 6
Transport ............................................................................... 5
Transporting .......................................................................... 9
Treating the heating water .................................................. 18
U
Unloading the box ................................................................. 9
Unpacking the product .......................................................... 9
V
Voltage .................................................................................. 5
W
Wall-mounting the product .................................................. 10
Weight ................................................................................. 10
To Next Page
Loading...
