GRANULDISK Granule Flexi

Questions and Answers

C
Courtney House PhDSep 23, 2025
What should I do if a temperature sensor in my GRANULDISK Washer returns a false reading?
- A
  Alicia RodriguezSep 23, 2025
  If one of the temperature sensors in your GRANULDISK Washer has returned a false reading, cut the power to the machine completely by switching the machine off at the wall socket. Wait 15 seconds. Switch the power back on. If the fault recurs, repeat the procedure once again. If the fault persists, contact service and ask them to replace one of the temperature sensors.
A
andrewfernandezSep 23, 2025
What does it mean if there is a system error and the control card is non operational on my GRANULDISK Washer?
- P
  Paul WongSep 23, 2025
  If you encounter a system error indicating the control card is non-operational on your GRANULDISK Washer, it signifies that a control card component is broken. Contact a service engineer!
J
Jonathan MartinAug 31, 2025
What to do if the motor protector for the right potwash pump tripped on my GRANULDISK Granule Flexi Washer?
- T
  theresamartinezAug 31, 2025
  If the motor protector for the right potwash pump has tripped on your GRANULDISK Washer, it indicates that the motor is overloaded. Contact a service engineer!
J
Jeremy PerezAug 25, 2025
What to do if the door switch alarm goes off on my GRANULDISK Granule Flexi?
- M
  Miguel DeleonAug 25, 2025
  If the door switch alarm activates on your GRANULDISK Washer, it indicates that the door was opened during operation. Close the door and press the STOP button to reset the alarm.
M
Mrs. Rachel HatfieldAug 25, 2025
What to do if the overheating protector for the wash tank tripped on my GRANULDISK Washer?
- D
  Donald FordAug 26, 2025
  If the overheating protector trips for the wash tank on your GRANULDISK Washer, it means the wash tank heater has overheated. Clean the level sensor in the wash tank and then reset the overheat protection. If the error happens again within a few hours, contact a service engineer.
W
William BrownAug 26, 2025
What to do if the overheating protector for the rinse tank tripped on my GRANULDISK Granule Flexi Washer?
- S
  seth81Aug 26, 2025
  If the overheating protector trips for the rinse tank on your GRANULDISK Washer, it means that the rinse tank heater has overheated. You should clean the level sensor and reset the overheat protection. If the error code returns within a few hours, contact a service engineer.
B
Brittany HughesAug 27, 2025
Why is the wash tank filling time so long on my GRANULDISK Washer?
- G
  gsmithAug 27, 2025
  If your GRANULDISK Washer is experiencing a long wash tank filling time, it means the wash tank filling has exceeded its time limit. Check the water supply to the machine and the rinse pump. Clean the rinse nozzles. Then, reset the alarm by pressing the STOP button. If the alarm continues, contact a service engineer.
L
Lucas JonesAug 27, 2025
Why is the rinse tank filling time so long on my GRANULDISK Washer?
- S
  Shelby AndersonAug 27, 2025
  If the rinse tank filling time is too long on your GRANULDISK Washer, it means the rinse tank filling has exceeded its time limit. Check the water supply to the machine and the solenoid valve for the rinse tank filling. Reset the alarm by pressing the STOP button. If the alarm continues, contact a service engineer.
C
Christian HarrisAug 28, 2025
What to do if the temperature is not reached in the wash tank of my GRANULDISK Granule Flexi Washer?
- M
  Mary PerezAug 28, 2025
  If the temperature isn't being reached in the wash tank of your GRANULDISK Washer, and the heating has been interrupted, clean the level sensor. Reset the overheat protection. If the error code continues to appear within a few hours, contact a service engineer.
K
Kristy WalkerAug 28, 2025
What to do if the temperature is not reached in the rinse tank of my GRANULDISK Granule Flexi Washer?
- F
  fredmorganAug 28, 2025
  If the temperature is not being reached in the rinse tank of your GRANULDISK Washer, and the ongoing process has been interrupted, clean the level sensor. Reset the overheat protection. If the error code continues to appear within a few hours, contact a service engineer.

GRANULDISK Granule Flexi Specifications

General

Water Consumption	15 liters per cycle
Material	Stainless Steel
Spin Speed	Not Applicable
Noise Level (Spinning)	Not Applicable
Energy Efficiency Class	Not Applicable