GRANULDISK Granule Flexi - User Manual

53 pages

Save Page as PDF

To Next Page

Art. no EN16265

Granuldisk AB retains the right to make technical changes to the products.

No responsibility is taken for any printing errors.

www.granuldisk.com Tel. +46 40 671 50 60

Granule

Flexi®

User Manual

Questions and Answers

F
Fernando YorkAug 29, 2025
Why is the rinse time so long on my GRANULDISK Washer?
- C
  coopersydneyAug 29, 2025
  If you're experiencing a long rinse time with your GRANULDISK Washer, it means the correct water volume hasn't been reached in time. Clean the rinse nozzles and reset the alarm by pressing the STOP button. If the alarm continues, contact a service engineer.
M
Matthew AtkinsAug 30, 2025
How do I clean the level sensor on my GRANULDISK Granule Flexi?
- E
  Evelyn EdwardsAug 30, 2025
  If you suspect the level sensor in your GRANULDISK Washer needs cleaning, it's likely dirty or the water hasn't been exchanged after a long shutdown. Lower the water level and clean the level sensor in the wash tank. Then, refill the tank. If the sensor is already clean, reset the error and set the machine in heating mode to continue heating.
M
Mary SchultzAug 30, 2025
Why is there a low water level and foam in my GRANULDISK Granule Flexi?
- M
  Matthew RhodesAug 31, 2025
  If you notice a low water level and foam in your GRANULDISK Washer, it's likely due to foam forming in the machine. Avoid using detergents designed for washing up by hand. Change the wash water. If the foaming issue continues, contact your detergent supplier. Reset the alarm by pressing the STOP button.
B
burnsdanielAug 25, 2025
How to fix a spray pipe alarm on a GRANULDISK Granule Flexi Washer?
- M
  Melissa WadeAug 25, 2025
  If you're getting a spray pipe alarm on your GRANULDISK Washer, it means something is blocking the spray pipes from moving. Remove whatever is obstructing their movement.
O
ocoxSep 1, 2025
What to do if the motor circuit breaker for the left pot wash pump tripped on my GRANULDISK Washer?
- P
  Patricia RobbinsSep 1, 2025
  If the motor circuit breaker for the left pot wash pump tripped on your GRANULDISK Washer, it means the motor is overloaded. Contact a service engineer!
B
Brandon Armstrong DDSSep 1, 2025
What to do if the motor circuit breaker for the rinse pump tripped on my GRANULDISK Granule Flexi?
- K
  Kristine ParksSep 2, 2025
  If the motor circuit breaker trips for the rinse pump on your GRANULDISK Washer, it means the motor is overloaded, and the program has been interrupted. Contact a service engineer!
C
Christopher HinesSep 2, 2025
What to do if the temperature sensor in the rinse tank is not working in my GRANULDISK Granule Flexi Washer?
- E
  Emily RoblesSep 2, 2025
  If the temperature sensor in the rinse tank of your GRANULDISK Washer is not working, it means the sensor is broken. Contact a service engineer!
T
Thomas FisherSep 3, 2025
What to do if the water level is too low in the rinse tank of my GRANULDISK Granule Flexi Washer?
- D
  Darius ConnerSep 3, 2025
  If the water level is too low in the rinse tank of your GRANULDISK Washer, it indicates the level has fallen incorrectly. Contact a service engineer!
S
Sarah WilliamsSep 4, 2025
What to do if the water level is too low in the wash tank of my GRANULDISK Granule Flexi?
- J
  joshua66Sep 4, 2025
  If the water level is too low in the wash tank of your GRANULDISK Washer, it indicates the level has fallen incorrectly. Contact a service engineer!
J
jenniferlopezSep 4, 2025
Why is the rinse time so short on my GRANULDISK Granule Flexi Washer?
- M
  Mary NelsonSep 4, 2025
  If you're experiencing a short rinse time on your GRANULDISK Washer, it means the rinse water was pumped out too fast, leading to insufficient heating and rinsing. Contact a service engineer!

GRANULDISK Granule Flexi Specifications

General

Water Consumption	15 liters per cycle
Material	Stainless Steel
Spin Speed	Not Applicable
Noise Level (Spinning)	Not Applicable
Energy Efficiency Class	Not Applicable