SYSTEM CONFIGURATION 23
It is best to select the Dolby Pro Logic mode for
making the speaker setup. Note that with the
actually selected input all settings will be copied
to other surround modes too (as far as possible).
To enter the proper settings for the speaker
setup, the easiest path is through the
SPEAKER SETUP menu (Figure 5
below).
1. Press the OSD button
I
to bring up the
AUDIO SET UP menu (Figure 1), and
then press the
¤ button
6
twice so that the
cursor is on the SPEAKER SETUP line.
At this point, press the Set button
8
to bring
up the SPEAKER SETUP menu
(Figure 5).
Figure 5
2.When the SPEAKER SETUP menu
first appears, the on-screen cursor
› will be at the
top of the list of speaker positions, pointing
toward the LEFT/RIGHTline, which sets
the configuration for the two front speakers. If you
wish to make a change to the front speakers, press
the
‹
/
›
buttons
9
so that either LARGE
or SMALL appears, matching the appropriate
description from the definitions shown above.
When SMALL is selected, low frequency front
channel sounds will be sent only to the subwoofer
output. Note that if you choose this option and
there is no subwoofer connected, you will not hear
any low frequency sounds from the front channels.
When LARGE is selected, a full-range output
will be sent to the front left and front right out-
puts, and with all analog surround modes the
front channel low frequency signals will be sent to
the subwoofer output.
Important Note: When a speaker set with two
front satellites and a passive subwoofer is used,
connected to the front speaker outputs
ª
, the
fronts must be set for LARGE.
3.When you have completed your selection for the
front channel, press the
¤
button
6
on the
remote to move the cursor to CENTER.
4. Press the
‹
/
›
buttons
9
on the remote
to select the option that best describes your
Center speaker based on the speaker definitions
shown on this page.
When SMALL is selected, low frequency center
channel sounds will be sent to the Fronts, if they
are set for LARGE and Sub is turned off.When
Sub is on, low frequency center channel sounds
will be sent to the subwoofer only.
When LARGE is selected, a full-range output
will be sent to the center speaker output, and
with analog and digital surround modes NO cen-
ter channel signal will be sent to the subwoofer
output.
When NONE is selected, no signal will be sent
to the center channel output. The receiver will
operate in a “phantom” center channel mode
and center channel information will be sent to
the left and right front channel outputs. This
mode is needed if no Center speaker is used.
5. When you have completed your selection for
the center channel, press the
¤
button
6
on
the remote to change the cursor to SUR-
ROUND.
6. Press the
‹
/
›
buttons
9
on the remote
to select the option that best describes the sur-
round speakers in your system based on the
speaker definitions shown on this page.
When SMALL is selected, low frequency sur-
round channel sounds will be sent to the Fronts,
when Sub is turned off, or to the subwoofer out-
put when Sub is on. In Pro Logic mode, there is
no bass in the surround channels.
When LARGE is selected, a full-range output
will be sent to the surround channel outputs
(with all analog and digital surround modes),
and, except with Hall and Theater modes, NO
surround channel signals will be sent to the sub-
woofer output.
When NONE is selected, surround sound infor-
mation will be split between the front-left and
front-right outputs. Note that for optimal per-
formance when no surround speakers are in use,
the Dolby 3 Stereo mode should be used instead
of Dolby Pro Logic.
7.When you have completed your selection for
the surround channel, press the
¤
button
6
on
the remote to move the cursor to SUBWOOFER.
8. Press the
‹
/
›
buttons
9
on the remote
to select the option that best describes your sys-
tem.
Select YESif a subwoofer is connected to your
system.
Select NOif a subwoofer is NOT connected to
your system. Note that when no subwoofer is
selected, low frequency sounds below 100Hz will
be sent to the front left and front right speakers
only. This option is not available when the front,
speakers are set to SMALL.
When a speaker set with two or more satellites
and a subwoofer is used, the front satellites and
the subwoofer must be connected to the front
speaker outputs
ª
and the subwoofer must be
set for NO.
9. When all speaker selections have been made,
press the
¤
button
6
and then the Set button
8
to return to main menu.
10. The Speaker Configuration may be changed
at any time without using the full-OSD on-screen
menu system by pressing the Speaker Select
button on the front panel
Û
or remote
.
Once the button is pressed, FNTSPEAK-
ERwill appear in both the lower third of the
video display and the Main Information
Display
W
.
Within five seconds, either press the front panel
‹
/
›
Selector buttons
5
or the
⁄
/
¤
buttons
6
on the remote to select a different speaker
position, or press the Set Button
(
8
to
begin the adjustment process for the front left
and right speakers
When the Set button
(
8
has been pressed
and the system is ready for a change to the
speaker setting, the on-screen display and Main
Information Display W will read FNT
LARGE or FNT SMALL depending on
the current setting. Press the front panel
‹
/
›
Selector Buttons
5
or the
⁄
/
¤
buttons
6
on the remote until the desired setting is shown,
using the instructions for “large” or “small”
shown earlier, then press the Set button
(
8
.
If another speaker position needs to be changed,
press the front panel
‹
/
›
Selector buttons
5
or the
⁄
/
¤
buttons
6
on the remote to
select a different speaker position, press the Set
button
(
8
and then press the front panel
‹
/
›
Selector buttons
5
or the
⁄
/
¤
buttons
6
on the remote until the correct speaker set-
ting is shown and press the Set button
(
8
again to confirm the selection.
To assist in making these settings, the icons in
the Speaker/Channel Input Indicators
P
will change as the speaker type is selected at
each position. When only the inner icon box con-
taining the abbreviation for the speaker position
is lit, the speaker is set for “small.”When the
inner box and the two outer boxes with circles
inside them are lit, the speaker is set for “large."
To Next Page
Loading...
