7 KEY PCB (37-2) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Remove the Front Panel ASS’Y, referring to the previous step 2 .
3. Remove the Fip PCB (37-1), referring to the previous step 6 .
4. Remove 10 screws (S2) and then remove the Key PCB (37-2).
8 TUNER MODULE (42) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Disconnect the card cable between connector (CON1-13p) on the Tuner module (42) and connector (CN13) on Input PCB (39-1).
3. Remove 2 screws (S8) and then remove the Tuner Module (42).
9 VIDEO PCB (41) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Disconnect the card cable between connector (BN14-13p) on the Video PCB (41) and connector (CN14) on the Input PCB (39-1).
3. Disconnect connector (CN43) on the Video PCB (41) from the lead wire (BN43-4P) on the Regulator PCB (A)(40-2).
4. Disconnect connector (CN41) on the Video PCB (41) from the lead wire (BN41-6P) on the Volume PCB (37-6).
5. Disconnect the card cable between connector (CN42) on the Video PCB (41) and connector (BN44-11p) on the I-Pod PCB (39-2).
6. Disconnect the card cable between connector (BN45-7p) on the Video PCB (41) and connector (CN45) on the HDMI PCB (42).
7. Remove 6 screws (S8) and then remove the Video PCB (41).
10 I-POD PCB (39-2) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Remove the Video PCB (41), referring to the previous step 9
3. Disconnect the card cable between connector (BN19-15p) on the I-Pod PCB (39-2) and connector (CN19) on the Input PCB (39-1).
4. Disconnect the card cable between connector (BN44-11p) on the I-Pod PCB (39-2) and connector (CN42) on the Video PCB (41).
5. Disconnect the card cable between connector (CN47-7p) on I-Pod PCB (39-2) and connector (CN47) on the RS232 PCB (37-7).
6. Disconnect board to board wafer between connector (BN17-12p) on I-Pod PCB (39-2) and connector (CN23) on the XM PCB (43).
7. Remove 2 screws (S13) and then remove the I-Pod PCB (39-2).
11 RS232 PCB (37-7) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Remove the Video PCB (41), referring to the previous step 9
3. Disconnect the card cable between connector (CN47) on the RS232 PCB (37-7) and connector (CN47-7) on RS232 PCB (37-7).
4. Remove 2 screws and then remove the RS232 PCB (37-7).
12 HDMI PCB (42) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Disconnect the card cable between connector (CN45) on the HDMI PCB (42) and connector (BN45-7p) on the Video PCB (41)
3. Remove 3 screws (S15) and then remove the hdmi PCB (42).
13 XM PCB (43) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Remove the Video PCB (41), referring to the previous step 9
3. Disconnect board to board wafer between and connector (CN23) on XM PCB (43) and connector (BN17-12p) on I-Pod PCB (39-2)
4. Disconnect the card cable between connector (BN21-7p) on xm PCB (43) nd connector (CN21) on the input PCB (39-1)
AVR245 harman/kardon
To Next Page
Loading...
