5. Disconnect the lead wire (BN85-2P) on the Xm PCB (43) from connector (CN85) on the Regulator PCB (A)(40-2).
6. Remove 1 screws (S15) and then remove the xm PCB (43).
14 INPUT PCB (39-1) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Remove the Tuner module (42), referring to the previous step 8
3. Remove the Video PCB (41), referring to the previous step 9
4. Disconnect connector (CN20) on the the Input PCB (39-1) from the lead wire (BN20-5P) on the Regulator PCB (B)(40-5).
5. Disconnect connector (CN22) on the Input PCB (39-1) from the lead wire (BN22-6P) on the Phone PCB (37-5).
6. Disconnect connector (CN18) on the Input PCB (39-1) from the lead wire (BN18-5P) on the Phone PCB (37-5)
7. Disconnect connector (CN10) on the Input PCB (39-1) from the lead wire (BN10-4P) on the Volume PCB (37-6).
8. Disconnect the card cable between connector (CN14) on the Input PCB (39-1) and connector (BN14-13p) on the Video PCB (41).
9. Disconnect the card cable between connector (CN19) on the Input PCB (39-1) and connector (BN19-15p) on the I-Pod PCB (39-2)
10. Disconnect the card cable between connector (CN21) on the input PCB (39-1) and connector (BN21-7p) on XM PCB (43).
11. Disconnect the card cable between connector (CN12-21p) on Input PCB (39-1) and connector (CN12-21p) on main PCB (38-1)
12. Disconnect the card cable between connector (CN11-17p) on the Input PCB (39-1) and connector (CN11) on the main PCB (38-1)
13. Disconnect the card cable between connector (CN72) on the Input PCB (39-1) and connector (CN72-17p) on the Fip PCB (37-1)
14. Remove 11 screws (S8,S15) and then remove the Input PCB (39-1).
15 POWER TRANS (36) & POWER PCB ASS’Y(40) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Disconnect lead wire of the Power Trans (36) from connector (CN91-3P) on the Main PCB (38-1)
3. Disconnect connector (CN19-3P,CN20-4P) on TRANS PCB (40-3) from the lead wire (BN19-3P,BN20-4P) on the Main PCB (38-1).
4. Disconnect the lead wire (BN96-8P) on the Power PCB (40-4) from connector (CN96) on the Regulator PCB (B)(40-5).
5. Disconnect the lead wire (BN99-8P) on the Power PCB (40-4) from connector (CN99) on the Regulator PCB (A)(40-2).
6. Disconnect connector (CN81) on the Trans PCB (40-4) from the lead wire (BN81-8P) on the Fip PCB (37-1).
6. Disconnect connector (CN85) on the Regulator PCB (A)(40-2) from the lead wire (BN85-2P) on the Xm PCB (43).
7. Remove 4 Trans screws (S9) and then remove the Power Trans (36) & Power PCB ASS’Y(40) REMOVAL .
16 REMOTE PCB ASS’Y(40-7) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Disconnect connector (CN88) on remote PCB (40-7) from the lead wire (BN88-3P) on the Main PCB (38-1)
3. Remove 3screws (S13) and then remove the Remote PCB ASS’Y(40-7).
17 MAIN PCB ASS’Y(38-1) REMOVAL
1. Remove the Top-cabinet, referring to the previous step 1 .
2. Remove the Tuner module (42), referring to the previous step 8 .
3. Remove the Video PCB (41) referring to the previous step 9 .
4. Remove the I-Pod PCB (39-2), referring to the previous step 10 .
5. Remove the RS232 PCB (37-7), referring to the previous step 11 .
6. Remove the XM PCB (43), referring to the previous step 13 .
7. Remove the Input PCB (39-1), referring to the previous step 14 .
8. Remove the AC Cord(35) on the Main PCB (38-1)
9. Disconnect the lead wire (BN90-2P) on the Main PCB (38-1) from connector (CN86) on Moms PCB (37-4).
10. Disconnect connector (CN91-3P) on the Main PCB (38-1) from lead wire of the Power Trans (36)
11. Disconnect the lead wire (BN89-2P) on the Main PCB (38-1) from connector (CN89) on Regulator PCB (A)(40-2).
12. Disconnect the lead wire (BN19-3P,BN20-4P) on Main PCB (38-1) from connector (CN19-3P,CN20-4P) on TRANS PCB (40-4).
13. Disconnect the lead wire (BN88-3P) on the Main PCB (38-1) from connector (CN88) on remote PCB (40-7).
14. Remove 11screws (S13-1EA, S4-2EA, S6-2EA, S8-6EA) and then remove the Main PCB ASS’Y(38-1).
AVR245 harman/kardon
To Next Page
Loading...
