EasyManua.ls Logo

Heath Zenith 5412 - User Manual

Heath Zenith 5412
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
© 2012 HeathCo LLC 204026-01A
Model 5412
Motion Sensor Light
Control
TEST
Features
• Turnsonlightingwhenmotionisdetected.
• Automaticallyturnslightingoff.
• Photocellkeepsthelightingoffduringdaylighthours.
• LEDindicatesmotionwassensed(dayornight).
TEST 1 5 10
ON-TIME
Put the ON-TIME switch on the
bottomofthesensorintheTEST
position.
OPERATION
*resetstoAutoModeatdawn.
ON-TIME
TEST 1 5 10
...backon.
1Second
OFF then...
PuttheON-TIMEswitchinthe1,5,
or10minuteposition.
Manual mode only works at night
becausedaylightreturnsthesensor
toAUTO.
Flipthelightswitchoffforonesecond
thenbackontotogglebetweenAUTO
andMANUALMODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Note:Whenrstturnedonwaitabout1
1
/
2
minutesfor
thecircuitrytocalibrate.
Thispackageincludes:
LightControl
Sensor
Cover
Plate
Bulb
Holders
Requirements
• Thelightcontrolrequires120-voltsAC.
• IfyouwanttouseManualMode,thecontrolmustbe
wiredthroughaswitch.
• Some codes require installation by a
qualified electrician.
• Thisproductisintendedforusewiththeenclosed
gasketandwithajunctionboxmarkedforuseinwet
locations.
Mode: On-Time Works: Day Night
Test
5Seconds x x
Auto
1,5,or10Minutes x
Manual
ToDawn* x
AUTO
MANUAL MODE
2Shells
PlasticHanger
RubberPlug
Gasket
6Screws
(3sizesincluded)
MountingStrap
MountingBolt
2Wire
Connectors
2FloodLamps
(NotIncludedwithall
Models)

Table of Contents

Other manuals for Heath Zenith 5412

Preview: Manual
Manual5 pages

Questions and Answers

  • G
    gilbertjosephJul 26, 2025
    How to fix Heath Zenith 5412 lights that won't turn on?
    • D
      dianebatesJul 26, 2025
      If your Heath Zenith Control Unit lights are not turning on, there could be several reasons. First, ensure the light switch is on. Check the flood lamp to see if it's loose or burned out, and replace it if needed. Also, verify that a fuse hasn't blown or a circuit breaker hasn't tripped; replace the fuse or reset the breaker if necessary. If it's daytime, the daylight turn-off feature may be active, so recheck after dark. For new installations, double-check the circuit wiring. Finally, make sure the light control is aimed correctly to cover the desired area.
  • J
    jhudsonJul 30, 2025
    Why do my Heath Zenith 5412 lights stay on all the time?
    • J
      Joel WestJul 30, 2025
      If the lights on your Heath Zenith Control Unit remain on continuously, there are a few potential causes. One possibility is that a flood lamp is positioned too close to the light control or pointed at nearby objects, causing heat to trigger the control. Repositioning the flood lamp away from the light control or nearby objects might resolve this. Another cause could be a heat source like an air vent or reflective surface triggering the light control; in this case, try reducing the range. Lastly, ensure the light control is not set to manual mode; switch it to AUTO.
  • D
    dyerchloeAug 4, 2025
    What to do if Heath Zenith Control Unit lights turn on randomly?
    • J
      James BallardAug 4, 2025
      If your Heath Zenith Control Unit lights are activating for no apparent reason, it could be that the light control is detecting small animals or automobile traffic. Try re-aiming the light control. It's also possible that the range is set too high; try reducing it.
  • A
    Amber PorterAug 8, 2025
    Why are my Heath Zenith 5412 lights flashing on and off?
    • D
      Daniel RoseAug 8, 2025
      If the lights on your Heath Zenith Control Unit are flashing on and off, several factors could be responsible. It's possible that heat or light from the flood lamps is triggering the light control intermittently. Try repositioning the flood lamp away from the light control. Reflected heat from other objects might also cause this issue, so reposition the light control. If the light control is in TEST mode and warming up, flashing is normal. Lastly, light leaking through the flood lamp reflectors could be the cause; replace the flood lamps with new, high-quality PAR 38 lamps, ensuring the metal lamp protectors are installed.
  • M
    Mrs. Kelsey BradleyAug 12, 2025
    Why does my Heath Zenith 5412 turn on during the day?
    • D
      Denise RayAug 13, 2025
      If your Heath Zenith Control Unit lights are activating during daylight, it could be that the light control is installed in a relatively dark location; in this case, the fixture is operating normally. Also, check if the light control is in TEST mode. If it is, set the control switch to 1, 5, or 10 minutes.
  • M
    Mrs. Sarah Barnett DDSAug 16, 2025
    Why do my Heath Zenith 5412 Control Unit lights turn off late in Dusk-to-Dawn setting?
    • V
      Vanessa RoseAug 16, 2025
      If your Heath Zenith Control Unit lights are turning off too late in the Dusk-to-Dawn setting, the light control may be installed in a relatively dark location. Consider relocating the light control, or use the 3-hour or 6-hour setting instead.
  • M
    Mrs. Lacey Thompson MDAug 21, 2025
    Why do Heath Zenith Control Unit lights flash once then stay off in manual mode?
    • E
      Emily WilliamsonAug 21, 2025
      If the lights on your Heath Zenith Control Unit flash once and then stay off in manual mode, the light control may be detecting its own lights. Try repositioning the flood lamps to keep the area below the light control relatively dark.

Summary

Requirements

Operation Modes

TEST Mode

Details on using the TEST mode for sensor calibration and initial setup.

AUTO Mode

Instructions for setting the automatic ON-TIME duration in AUTO mode.

MANUAL MODE

Guide to activating and using the MANUAL MODE for light control.

Installation

Wall Mount

Steps for mounting the light control on a wall surface.

Eave Mount

Procedure for installing the sensor head for eave mounting.

Wiring the Light Control

Mounting the Light Control

Test and Adjustment

Specifications

Troubleshooting Guide

Technical Service

Warranty Information

Heath Zenith 5412 Specifications

General IconGeneral
BrandHeath Zenith
Model5412
CategoryControl Unit
LanguageEnglish

Related product manuals