HEIDENHAIN TNC 151 Q - Combined Technical Specifications

6.2.4
6.3
6.4
6.4.1
6.4.2
6.4.2.1
6.4.2.2
6.4.2.3
6.4.2.4
6.4.3
6.5
6.6
Machine parameters which are determined after compilation of the parameters for the ramp
characteristic
54
Machine parameters in conjunction with the PLC -
56
Machine parameters in conjunction with the RS-232-C (V.24) data interface 57
F/S-232-C standard data interface via “EXT’‘-mode 59
Operating mode “Transfer blockwise” 60
“Transfer blockwise” using, the HEI DENHAIN Floppy disc unit FE 401 60
“Transfer blockwise” via EXT-mode
60
“Transfer blockwise” from a peripheral unit to the TNC 151/TNC 155
64
Characters and block formats for various operating modes 65
Hardcopy printout of graphics (TNC 155 only)
66
Machine parameters for handwheels and touch probe systems 67
Machine parameters for 3D-Touch probe systems 67
7.
7.1
7.2
7.2.1
7.2.2
7.3
8.
8.1
8.2
8.3
8.3.1
8.3.2
8.3.3
8.4
8.4.1
8.4.2
8.4.3
8.5
8.6
8.7
8.7.1
8.7.2
8.8
8.8.1
8.8.2
8.8.3
8.9
Commissioning
68
Dialogue in 2 languages 68
Check list for commissioning 69
Checks prior to machine switch-on 69
Checks after switch-on of adaptor cabinet
70
Memory test after switch-on
70
Optimization of TNC 151/TNC 155-parameters
71
Adjustment check-list
71
Axis designation for NC-machines and “right-hand-rule”
72
Selection of machine axes
73
Assignment of transducer inputs to the control - internal axes
73
Axis switchover for axis IV
73
Designation of axis IV
73
Input/Output diagram for machine parameters
74
Read-in of machine parameters when memory erased
74
Alteration of machine parameters
75
Checking and correction of axis-traversing and counting directions
77
Setting software limit switch ranges
78
Offset adjustment
78
“Linear ramp characteristic” adjustment
80
Fine adjustment of trailing error for “linear ramp characteristic”-
80
Acceleration (linear and radial)
82
Adjustment of “square root characteristic”
83
Run-in behaviour with acceleration for “square root characteristic”-
84
Approach speed 1 urn before nominal position for “square root characteristic”
85
Position supervision for “square root characteristic”
85
Integral factor X, Y, Z, IV
86
9. Customized macros
87
9.1 Dialogue languages
88
9.2 Testing of customized macros
88
9.3 Repetition of customized macros
88
9.4 Example of a customized macro
89
9.5 Programming of a customized macro within the NC-program memory
90
9.6 Nesting of customized macros
91
9.7 Special function of parameters
91
9.8
Binary output of customized macros for programming a PLC-EPROM
92
9.9 Customized macros within a machining program
93
9.9.1 Example: Definition of the customized macro “Bolt hole circle” in a machining program-
93
9.9.2
Machining program using the macro “Bolt hole circle”
94
10. Spindle orientation (optional)
95
10.1
Machine parameters for spindle orientation
95
10.2
Spindle orientation with standard PLC-program
96
11.
12.
13.
14.
List of machine parameters
97
Adapter cables
104
Dimensions
106
Connections and PLC-allocation
_,’
112
3