How to fix a Heiniger Pet Care Product when the top blade does not move?
If the top blade of your Heiniger Pet Care Product isn't moving, here's what you can check: * The clipperhead may not be well engaged: Engage the clipperhead correctly when the motor is running. * The turning lever may be defective: Replace turning lever (S). * The top and bottom blades may stick to each other: Clean and oil the blades.
Why does my Heiniger Pet Care Product battery run out quickly?
If the running time of your Heiniger Pet Care Product's fully charged battery is too short, and/or the blades are getting hot: * The clipper blades may not have been oiled sufficiently: Oil clipper blades. * A dead, not fully charged, or defective battery may have been used: Only use an intact and completely charged original battery.
Why is my Heiniger Pet Care Product motor not running?
Your Heiniger Pet Care Product motor might not be running due to several reasons: * The battery may be dead: Charge the battery. * The contacts may be dirty: Switch the clipper off and clean the contacts. * The battery may be faulty: Replace the battery. * The motor may be burned out: Have the motor and / or electronics replaced (S). * The clipperhead may be blocked: Clean and oil the clipperhead.
What to do if my Heiniger Opal clipper cuts badly?
If your Heiniger Pet Care Product clipper cuts poorly, consider these potential causes and solutions: * The clipper blade may be blunt: Have top and bottom blades resharpened by service centre (S). * The clipper blades may not be oiled: Oil clipper blades every 15 minutes. * The animal‘s hair may be wet: Only clip dry hair. * Hairs may be jammed between top and bottom blades: Take off clipperhead, push the top blade half away from the clipperhead, take away hairs between top and bottom blade. * The clipperhead may have too little clipping pressure: Have clipperhead inspected (S).
What to do if the charging station light doesn't change on my Heiniger Opal?
If, when the battery is flat, the light of the charging station does not change from green to red on your Heiniger Pet Care Product: * The contacts of the battery and/or charging station may be dirty: Clean contacts. * The battery may be faulty: Replace the battery. * The battery may be exhausted: Place the battery in the charging station for at least 20 minutes. Replace the battery if the charging process fails to start. * The contacts of the charging station may be deformed: Have the charging station repaired (S).
Why is there no speed difference on my Heiniger Opal?
If you notice no speed difference between level I and level II on your Heiniger Pet Care Product, it could be due to faulty motor and / or electronics. In this case, notify customer service.
Why is the control light off on my Heiniger Pet Care Product charging station?
If the control light of the charging station is not on for your Heiniger Pet Care Product, it could be due to: * The charging station not being connected to the power supply: Connect the charging station to the power supply. * The charging station being faulty: Have charging station inspected (S).
What to do if no data is displayed on my Heiniger Opal charging status display?
If no data is displayed on the charging status display of your Heiniger Pet Care Product: * The battery might be exhausted: Place the battery in the charging station. * The battery might be faulty: Replace the battery.
Operator experience and restrictions for using the clipper on animals.
Safety precautions related to electrical power supply and preventing electric shock.
Safety considerations and warnings when clipping animals.
Guidelines for safe charging, placement, and handling of the battery.
Warnings regarding sharp blades and potential injuries.
Critical safety warnings to prevent fire, shock, burns, and injuries.
Steps for setting up the charging station and preparing the clipper for first use.
Procedures for clipping, changing parts, lubrication, and cleaning the clipper.
Guidance on how to safely and effectively clip animals.
Importance and method of lubricating clipper blades for optimal performance.
General| Battery Type | Lithium-ion |
|---|---|
| Run Time | 240 minutes |
| Speed Settings | 2 |
| Battery Voltage | 7.2 V |
| Type | Cordless Clipper |
| Motor | Brushless |
| Voltage | 100-240 V |
| Blade Type | Snap-on |
| Battery Life | 4 hours |
| Weight | 415 g |
| Speed | 2600 / 3100 dbs/min |
| Charge Time | 60 minutes |
To Next Page
