HELIX P SIX DSP MK2 Installation Instructions

26
8OWUD +' &ODVV ' DPSOL¿HU WHFKQRORJ\ ZLWK
96 kHz sampling rate
7KH+(/,;36,;'630.LVWKH¿UVW&ODVV'DP-
SOL¿HUZLWKLQWHJUDWHG'63RQWKHPDUNHWWKDWUXQV
at 96 kHz sampling rate. Therefore the audio band-
width is no longer limited to 22 kHz, but allows an
extended frequency response to more than 40 kHz.
The higher sampling rate has only been possible
E\LPSOHPHQWLQJWKHODWHVW'63DQGDPSOL¿HUFKLS
sets.
7KH UHVXOW D &ODVV 'DPSOL¿HU ZLWK DQ XQSUHFH-
dented sound quality.
Ready for 24 V
It is possible to operate the P SIX DSP MK2 with a
supply voltage of 12 Volts or 24 Volts (e.g. as usual
in trucks) without the need to make any changes
to the unit.
,Q ERWK RSHUDWLQJ PRGHV WKH DPSOL¿HU ZLOO KDYH
equal performance characteristics. This guarantees
PD[LPXPÀH[LELOLW\IRUQXPHURXVDSSOLFDWLRQV
Power Save Mode
The Power Save Mode is incorporated in the ba-
VLFVHWXS,WDOORZVWRVLJQL¿FDQWO\UHGXFHWKHSRZHU
consumption of the P SIX DSP MK2 and connected
DPSOL¿HUVRQFHWKHUH¶VQRLQSXW VLJQDO SUHVHQWIRU
more than 60 seconds. Please note that in many
XSWRGDWH FDUV ZLWK ³&$1´ RU DQ\ RWKHU LQWHUQDO
bus structures it may happen that the radio remains
³LQYLVLEO\´ WXUQHG RQ IRU XS WR  PLQ HYHQ DIWHU
OHDYLQJ WKH FDU 2QFH WKH ³3RZHU 6DYH 0RGH³ LV
active the remote output (Rem Out) and the inter-
QDODPSOL¿HU VWDJHVZLOO EHWXUQHG RII7KH+(/,;
P SIX DSP MK2 will reactivate the remote output
DQGWKHLQWHUQDODPSOL¿HUVWDJHVZLWKLQDVHFRQGLID
music signal is applied. It is possible to either mod-
ify the turn-off time of 60 sec. or completely deacti-
YDWHWKH³3RZHU6DYH0RGH´YLDWKH'633&7RRO
software.
Start-/Stop capability
The switched power supply of the HELIX
P SIX DSP MK2 assures a constant internal supply
voltage even if the battery’s voltage drops to 6 Volts
during engine crank.
Automatic Digital Signal Detection
Switching from analog input to the digital input is
done automatically as soon as a signal is detect-
ed on the Optical Input. This feature can be deac-
tivated in the DSP PC-Tool software. Alternatively
you can use an optional remote control for manual
switching between analog and digital inputs.
Unique Features of the HELIX P SIX DSP MK2

HELIX P SIX DSP MK2 Specifications

General

Brand	HELIX
Model	P SIX DSP MK2
Category	Amplifier
Language	English