Why does the service indicator light on after changing carbon brushes in my Hilti Drill?
If the service indicator light illuminates after changing the carbon brushes on your Hilti Drill, it means that the contact surfaces are not yet run in. Run in the carbon brushes by allowing the power tool to run under no load for at least 1 minute without interruption.
Why doesn't my Hilti Drill achieve full power?
If your Hilti Drill doesn't achieve full power, it could be due to an inadequate gauge (cross section) of the extension cord conductors. Use an extension cord with an adequate conductor cross section. Alternatively, the voltage provided by the electric supply may be too low. Try connecting the drill to a different electric supply.
What to do if my Hilti Drill doesn't start?
If your Hilti Drill doesn't start, first check for any power interruption by plugging in another electrical tool to see if it works. If there was a power interruption, the electronic restart interlock may be activated. Try switching the power tool off and then on again.
Why is the drill bit not rotating on my Hilti TE 50-AVR?
If the drill bit doesn’t rotate on your Hilti Power Tool, it might be because the function selector switch is not engaged or is in the incorrect position. Ensure the function selector switch is set to “Drilling without hammering” or “Hammer drilling”.
What to do if my Hilti TE 50-AVR doesn't start and the service indicator is red?
If your Hilti Power Tool doesn't start and the service indicator shows red, it could be due to: * Worn-out carbon brushes. You should have the power tool checked by a trained electrical specialist, and the carbon brushes replaced if necessary. * An electrical fault. In this case, have the tool checked by Hilti Service.
What to do if drill bit can’t be released from Hilti TE 50-AVR Power Tool?
If you can't release the drill bit from your Hilti Power Tool, it might be due to: * The chuck not being pulled back fully. Pull the chuck back as far as it will go and then try removing the accessory tool. * The side handle not being fitted correctly. Release the side handle and refit it correctly so that the clamping band and side handle engage in the recess.
How to restart Hilti Power Tool?
If your Hilti Power Tool doesn't start, it might be due to the electronic restart interlock being activated after a power interruption. Try switching the power tool off and then on again to resolve this.
How to release chisel from Hilti Drill chuck?
If the chisel cannot be released from the chuck of your Hilti Drill, it may be because the chuck is not pulled back fully. Pull the chuck back as far as it will go and then remove the accessory tool.
Why doesn't the drill bit rotate on my Hilti Drill?
If the drill bit on your Hilti Drill doesn’t rotate, the function selector switch might not be engaged or is in the incorrect position. Set the function selector switch to “Drilling without hammering” or “Hammer drilling”.
How to fix no hammering action on Hilti Drill?
If your Hilti Drill has no hammering action, it might be too cold. Bring the tip of the drill bit into contact with the working surface, switch the rotary hammer on and allow it to run. Repeat this procedure if necessary, until the hammering mechanism begins to operate.
General| Drilling | Yes |
|---|---|
| Chuck type | SDS Max |
| Product color | Black, Red |
| Country of origin | Germany |
| Impact rate | 3180 bpm |
| Rated speed (max) | 360 RPM |
| Impact energy (max) | 6 J |
| Vibration level (hammer drilling) | 9 m/s² |
| Drilling diameter in concrete (max) | 40 mm |
| Optimum drilling diameter (concrete) | 16 - 32 mm |
| Input power | 1100 W |
| Power source | AC |
| Power plug type | Type C |
| Noise level | 108 dB |
| Quantity per shipping (inner) case | 1 pc(s) |
Weight and Dimensions| Weight | 6100 g |
|---|---|
| Package depth | 3456 mm |
| Package width | 2000 mm |
| Package height | 4500 mm |
| Package weight | 4500 g |
To Next Page
