What does it mean when the service indicator lights red on my Hilti TE 70-AVR Power Tool?
If the service indicator on your Hilti Power Tool is constantly lit red, the carbon brushes are worn. Have them checked, and if necessary replaced, by a trained electrical specialist.
What to do if the drill bit does not rotate on my Hilti TE 70-AVR?
If your Hilti Power Tool drill bit isn't rotating, the function selector switch may not be correctly engaged. Ensure the motor is at a standstill, then set the function selector switch to the "Hammer drilling" position.
Why doesn't my Hilti TE 70-AVR drill bit rotate?
If your Hilti Power Tool drill bit isn't rotating, the function selector switch might not be engaged or is in the "Chiseling" or "Chisel positioning" position. With the motor at a standstill, set the function selector switch to the “Hammer drilling” position.
How to release a stuck drill bit from my Hilti Power Tool?
If you can't release the drill bit from your Hilti Power Tool, the chuck might not be pulled back fully. Pull the chuck back as far as it will go and remove the accessory tool. Also, the side handle might not be fitted correctly. Disengage the side handle and refit it correctly so that the clamping band and side handle engage in the recess.
What to do if my Hilti Drill does not start?
If your Hilti Drill (Combihammer) doesn't start, there might be an interruption in the electric supply. Try plugging in another electric tool to check if the outlet works. Another reason could be that the generator is in sleep mode, in this case apply a load to the generator by connecting a second power consumer, then switch the tool off and on again. Also, the electronic restart interlock may be activated after a power interruption, so switch the power tool off and then on again. Finally, the carbon brushes may be worn, have them checked and replaced by a trained electrical specialist if needed.
Why does my Hilti Drill not achieve full power?
If your Hilti Drill (Combihammer) isn't achieving full power, first ensure the control switch is fully pressed. If that doesn't work, the extension cord may be too long or the conductor cross-section might be inadequate; use an extension cord of an approved length and adequate conductor cross-section. Also, the voltage provided by the electric supply could be too low, so connect the power tool to a different power source. Finally, if you are using TE 70-ATC/AVR or TE 80-ATC/AVR model, check if the half-power button is engaged and press it to disengage.
Why Hilti Rotary Hammer combihammer does not achieve full power?
If your Hilti Rotary Hammer combihammer isn't achieving full power, several factors could be responsible. Check if the extension cord is too long or has an inadequate conductor cross-section; use an approved length and adequate conductor. Ensure the control switch is fully pressed. Verify the voltage provided by the electric supply is adequate; try a different power source. Also, on TE 70-ATC/AVR and TE 80-ATC/AVR models, check if the half-power button is engaged and press it to disengage.
How to troubleshoot a Hilti Power Tool combihammer that does not start?
If your Hilti Power Tool combihammer won't start, begin by checking for any interruptions in the electric supply. Plug another electric tool into the same outlet to confirm it's working. If you're using a generator, it might be in sleep mode; try applying a load by connecting another device like a worklight, then switch the tool off and on again. An activated electronic restart interlock after a power interruption could also be the culprit; simply switch the power tool off and then on again. Finally, worn carbon brushes could be the issue, consult with a trained electrical specialist to check and replace them if needed.
What to do if the service indicator blinks red on my Hilti Drill?
If the service indicator blinks red on your Hilti Drill, it indicates a fault has occurred in the tool. Have the product repaired by Hilti Service.
Why is my Hilti TE 70-AVR Power Tool combihammer not achieving full power?
If your Hilti Power Tool combihammer isn't reaching its full power, several factors could be at play. First, ensure that your extension cord is neither too long nor has an inadequate conductor cross-section; if it is, use an extension cord of an approved length and / or of adequate conductor cross- section. Next, verify that you're fully pressing the control switch. Also, check that the voltage from your power supply isn't too low; if it is, connect the tool to a different power source. Lastly, for models TE 70-ATC/AVR and TE 80-ATC/AVR, confirm that the half-power button isn't engaged; if it is, press the half-power button.
General| Category | Power Tool |
|---|---|
| Type | Rotary Hammer |
| Single Impact Energy | 11.5 J |
| Hammer Drilling Diameter Range | 12 - 40 mm |
| Drilling Diameter Range (Hammer Drill Bits) | 12 - 40 mm |
| Dust Removal Module Available | Yes |
| Power Source | Corded Electric |
| Voltage | 230 V |
| Drilling Mode | Hammer drilling, chiseling |
| Vibration Reduction | Active Vibration Reduction (AVR) |
| Drilling Diameter Range (Hollow Drill Bits) | 40 - 100 mm |
| Full Hammering Frequency | 3510 impacts/minute |
| Blows Per Minute | 2760 BPM |
| Sound Pressure Level | 91 dB(A) |
| Tool Chuck Type | SDS-max |
| Tool Holder | SDS-max |
| Vibration Level | 9.6 m/s² (Hammer drilling into concrete) |
To Next Page
