What to do if Hilti Drill bit is not released?
If your Hilti Drill bit is stuck and not released, make sure that the chuck is pulled back fully. Pull the chuck back as far as it will go and remove the accessory tool. Also, check the side handle, it may not be fitted correctly. Disengage the side handle and refit it correctly so that the clamping band and side handle engage in the recess.
Why is there no hammering action on my Hilti Drill?
If your Hilti Drill is not hammering, it could be because the power tool is too cold. Try bringing the tip of the accessory tool into contact with the working surface, switch the power tool on, and allow it to run. Repeat if necessary, until the hammering mechanism begins to operate.
What does it mean when the service indicator lights red on my Hilti Drill?
If the service indicator light on your Hilti Drill is red, the carbon brushes are worn. Have them checked and replaced by a trained electrical specialist.
How to fix a Hilti Drill bit that does not rotate?
If your Hilti Drill bit does not rotate, the function selector switch might not be correctly engaged. Ensure that the motor is at a standstill and set the function selector switch to the “Hammer drilling” position.
Why does my Hilti Drill not achieve full power?
If your Hilti Drill (Combihammer) isn't achieving full power, first ensure the control switch is fully pressed. If that doesn't work, the extension cord may be too long or the conductor cross-section might be inadequate; use an extension cord of an approved length and adequate conductor cross-section. Also, the voltage provided by the electric supply could be too low, so connect the power tool to a different power source. Finally, if you are using TE 70-ATC/AVR or TE 80-ATC/AVR model, check if the half-power button is engaged and press it to disengage.
What to do if my Hilti Drill does not start?
If your Hilti Drill (Combihammer) doesn't start, there might be an interruption in the electric supply. Try plugging in another electric tool to check if the outlet works. Another reason could be that the generator is in sleep mode, in this case apply a load to the generator by connecting a second power consumer, then switch the tool off and on again. Also, the electronic restart interlock may be activated after a power interruption, so switch the power tool off and then on again. Finally, the carbon brushes may be worn, have them checked and replaced by a trained electrical specialist if needed.
How to release a stuck drill bit from my Hilti Power Tool?
If you can't release the drill bit from your Hilti Power Tool, the chuck might not be pulled back fully. Pull the chuck back as far as it will go and remove the accessory tool. Also, the side handle might not be fitted correctly. Disengage the side handle and refit it correctly so that the clamping band and side handle engage in the recess.
Why doesn't my Hilti TE 70-AVR drill bit rotate?
If your Hilti Power Tool drill bit isn't rotating, the function selector switch might not be engaged or is in the "Chiseling" or "Chisel positioning" position. With the motor at a standstill, set the function selector switch to the “Hammer drilling” position.
What to do if the drill bit does not rotate on my Hilti TE 70-AVR?
If your Hilti Power Tool drill bit isn't rotating, the function selector switch may not be correctly engaged. Ensure the motor is at a standstill, then set the function selector switch to the "Hammer drilling" position.
General| Category | Power Tool |
|---|---|
| Type | Rotary Hammer |
| Single Impact Energy | 11.5 J |
| Hammer Drilling Diameter Range | 12 - 40 mm |
| Drilling Diameter Range (Hammer Drill Bits) | 12 - 40 mm |
| Dust Removal Module Available | Yes |
| Power Source | Corded Electric |
| Voltage | 230 V |
| Drilling Mode | Hammer drilling, chiseling |
| Vibration Reduction | Active Vibration Reduction (AVR) |
| Drilling Diameter Range (Hollow Drill Bits) | 40 - 100 mm |
| Full Hammering Frequency | 3510 impacts/minute |
| Blows Per Minute | 2760 BPM |
| Sound Pressure Level | 91 dB(A) |
| Tool Chuck Type | SDS-max |
| Tool Holder | SDS-max |
| Vibration Level | 9.6 m/s² (Hammer drilling into concrete) |
To Next Page
