What to do if Hirschmann iSCOUT expert compact Music Mixer displays 'Lowered below radius range or angle range exceeded'?
If the Hirschmann Music Mixer displays 'Lowered below radius range or angle range exceeded', it means you have fallen below the minimum radius or gone past the maximum angle specified in the respective load chart because the boom was raised too far. To fix this, lower the boom to a radius or angle specified in the load chart.
What to do if Hirschmann Music Mixer displays 'Below lower limit value in measuring channel "angle main boom"'?
If the Hirschmann Music Mixer displays 'Below lower limit value in measuring channel "angle main boom"', it could be caused by a defective or loose cable between the central unit and the angle sensor, water inside the plug of the angle sensor, a defective angle potentiometer, or a defective electronic component in the measuring channel. Check the cable and plugs, replacing them if necessary. If that doesn't work, replace the sensor unit.
What to do if Hirschmann iSCOUT expert compact displays 'Below lower limit value in measuring channel "force main boom right"'?
If the Hirschmann Music Mixer displays 'Below lower limit value in measuring channel "force main boom right"', it could be due to a defective or loose cable between the central unit and the force transducer, or water inside the plug of the transducer, or a defective force transducer or an electronic component in the measuring channel. Check the cable and plugs, and replace them if necessary. Replace the sensor unit if needed.
What to do if Hirschmann Music Mixer displays 'Maximum force in the main boom pendants exceeded'?
If the Hirschmann Music Mixer displays 'Maximum force in the main boom pendants exceeded', it means the force actuating on the main boom pendants has exceeded the programmed value. Reduce the force acting on the main boom pendants.
What to do if Hirschmann iSCOUT expert compact Music Mixer displays 'Too large difference of the luffing jib angles at tip and base jib'?
If the Hirschmann Music Mixer displays 'Too large difference of the luffing jib angles at tip and base jib', it indicates that the angle as to the horizontal on the jib head exceeds the luffing jib angle by more than 5 degrees. Check the angle sensor on the jib head and the angle sensor on the jib base.
What to do if Hirschmann Music Mixer displays 'Too large difference of the boom angles at tip and base boom (if avail.)'?
If the Hirschmann Music Mixer displays 'Too large difference of the boom angles at tip and base boom (if avail.)', it means the angle as to the horizontal on the boom head exceeds the main boom angle by more than 5 degrees. Check the angle sensor on the boom head and the angle sensor on the base boom.
What to do if Hirschmann iSCOUT expert compact displays 'Faulty positioning of the jib during operation with fixed angle to the main boom or to a luffing jib'?
If the Hirschmann Music Mixer displays 'Faulty positioning of the jib during operation with fixed angle to the main boom or to a luffing jib', it means that during operation with a fixed jib to the main boom, the jib is not in the permitted angle range, or the angle measurement of the jib is defective. Luff the auxiliary jib to the permitted range and verify the angle measurement of the auxiliary jib.
What to do if Hirschmann iSCOUT expert compact displays 'Faulty main boom position during luffing jib operation'?
If the Hirschmann Music Mixer displays 'Faulty main boom position during luffing jib operation', it indicates that during luffing jib operation, the main boom is not in the prescribed angle range, or the angle measurement of the main boom is defective. Luff the boom to the permitted range and check the angle measurement of the main boom.
What to do if Hirschmann iSCOUT expert compact displays 'Radius range exceeded or lowered below angle range with luffing jib operation'?
If the Hirschmann Music Mixer displays 'Radius range exceeded or lowered below angle range with luffing jib operation', it means the maximum radius as specified in the load chart has been exceeded or you have lowered below the minimum angle due to lowering the luffing jib too far. Raise the jib to a radius or angle specified in the load chart.
What to do if Hirschmann Music Mixer shows 'Battery empty'?
If the Hirschmann Music Mixer displays a 'Battery empty' message, it means the battery check detected a low voltage. You should change and set up the battery. As a temporary solution, you can press the alarm off button to work without the data logger.
Details the step-by-step process of the LMI system's operation.
Describes the functions and location of the LMI operator console.
Identifies and explains the various displays and buttons on the console.
Explains the meaning of different status symbols shown on the display.
Guides the operator through setting up the crane's operating mode.
Explains how to quickly change hoist settings during operation.
Describes how to program limits for the crane's operating range.
Details how to set minimum and maximum boom radius limits.
Explains how to set minimum and maximum tip height limits.
Details how to set minimum and maximum boom angle limits.
Covers setting slewing angle limits and virtual wall definitions.
Explains how to define virtual walls to limit the working area.
Describes the final operational checks and verification after setup.
Explains how to access system information and service menus.
Explains how error codes are displayed and their general meaning.
Lists specific fault codes, causes, and elimination steps for the LMI system.
Explains how shut-off values are determined for boom cranes.
Discusses electromagnetic compatibility and preventive measures.
Provides safety guidelines for repairing display and control consoles.
Details installation requirements for specific console types.
General| Brand | Hirschmann |
|---|---|
| Model | iSCOUT expert compact |
| Category | Music Mixer |
| Language | English |
To Next Page
