Hitachi CP-WU8450 User Manual

117
Message Description
The horizontal or vertical frequency of the input
signal is not within the specied range.
Please conrm the specs for your projector or the signal
source specs.
An improper signal is input.
Please conrm the specs for your projector or the signal
source specs.
The internal temperature is rising.
Please turn the power off, and allow the projector to cool
down at least 20 minutes. After having conrmed the
following items, please turn the power ON again.
• Is there blockage of the air passage aperture?
• Is the air lter dirty?
• Does the peripheral temperature exceed 45°C?
• If you use CP-X8150, CP-WX8240, CP-SX8350 or
CP-WU8440, does the peripheral temperature exceed
40°C?
• Is the setting for ALTITUDE appropriate?
For details of ALTITUDE, refer to ALTITUDE of
SERVICE in the OPTION menu (

67). If the projector is
used with a wrong setting, it may cause damage to the
projector itself or the parts inside.
A note of precaution when cleaning the air lter.
Please immediately turn the power off, and clean or
change the air lter referring to the Cleaning and
replacing the air lter section of this manual. After you
have cleaned or changed the air lter, please be sure to
reset the lter timer (

65, 113).
The button operation is not available.
Check the button you are going to use (

6). Even when
a usable button is pressed, all button operations are not
available under the following conditions.
- While the lens is moving, button operation from the
control panel or the remote control might be ignored.
- Pressing the one of buttons to call a signal input might
be ignored, when all the input ports belonging to the
category the button's name shows are set to the "SKIP"
by the item SOURCE SKIP of the OPTION menu.
Troubleshooting
Related messages (continued)

Hitachi CP-WU8450 Specifications

General

Matrix size	0.76 \
Matrix type	3-panel (p-Si TFT active)
Native aspect ratio	16:10
Projection distance	1 - 38.3 m
Projection technology	LCD
Contrast ratio (typical)	3000:1
Screen size compatibility	30 - 600 \
Projector native resolution	WUXGA (1920x1200)
Audio input	3
RS-232 ports	1
Zoom capability	Yes
Focal length range	- mm
Lamp type	UHP
Lamp power	330 W
Lamps quantity	1 lamp(s)
Light source type	Lamp
Service life of light source	- h
3D	-
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1360 x 768 (WXGA), 1400 x 1050 (SXGA+), 1440 x 900 (WXGA+), 1600 x 1200 (UXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
RMS rated power	16 W
Number of built-in speakers	2
DVI port	No
BNC input ports	5
USB connector type	USB Type-A, USB Type-B
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	0
Noise level	- dB
Certification	UL/cUL, FCC Part15 class A, AS/NZS CISPR22 class A, CE, GOST-R
Placement	Desktop, Ceiling
Product type	Standard throw projector
Product color	White
Power source	AC
AC input voltage	100 - 240 V
Power consumption (standby)	- W
Operating temperature (T-T)	0 - 45 °C
Sustainability certificates	RoHS

Weight and Dimensions

Depth	396 mm
Width	498 mm
Height	135 mm
Weight	8700 g