Hitachi CP-WU8450 User Manual

22
When the projector is in a normal condition,
or dislays one of the warnings of AIR FLOW,
COLD or FILTER errors, press the FUNCTION
button on the control panel or press the ENTER
button on the remote control for three seconds.
The backlight of the monitor turns on.
 To display the setup information including
usage time
Use the ◄/► buttons to switch display.
Usage time: The Status Monitor displays
the lamp time (usage time of the present
lamp), the lter time (usage time of the air
lter) and the projector usage time.
Network information: The network information is displayed over three pages.
Use the ▲/▼ buttons to switch the page.
Displayed information in each page is as below;
2nd page
: Subnet mask
(wireless and wired)
1st page
: IP address
(wireless and wired)
3rd page
: Default gateway
(wireless and wired)
(continued on next page)
2
N 1 9 2 1 6 8 0 0 1 0 7 5
W 1 9 2 1 6 8 0 0 1 9 6
I P A D D R E S S
S Y S T E M 2 2 3 8 6 h
F I L T E R 1 2 8 3 5 h
0 L A M P 2 2 5 0 h
Status Monitor <Only for CP-X8160, CP-WX8250 and CP-WU8450>
Displaying the log
The present setup information and the error history can be displayed on the
Status Monitor with button operation.
• While the projector is warming up, button presses are ignored.
• When the USB TYPE A port is selected, use the buttons on the control panel
to display the logs. The button operation of the Status Monitor on the remote
control may be unavailable.
• The Status Monitor displays nothing or no button presses for the monitor are
available while the projector is in standby mode if the STANDBY MODE item of
SETUP menu is set to SAVING (
54).
•
Both of the Status Monitor and the OSD menu cannot be operated at same time.
NOTE
FUNCTION
button
ENTER
button
Usage time (example)
Network information
(example)
First display Usage time
Network
information
Lamp time
Filter time
Projector
usage time
Wired
Wireless

Hitachi CP-WU8450 Specifications

General

Matrix size	0.76 \
Matrix type	3-panel (p-Si TFT active)
Native aspect ratio	16:10
Projection distance	1 - 38.3 m
Projection technology	LCD
Contrast ratio (typical)	3000:1
Screen size compatibility	30 - 600 \
Projector native resolution	WUXGA (1920x1200)
Audio input	3
RS-232 ports	1
Zoom capability	Yes
Focal length range	- mm
Lamp type	UHP
Lamp power	330 W
Lamps quantity	1 lamp(s)
Light source type	Lamp
Service life of light source	- h
3D	-
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1360 x 768 (WXGA), 1400 x 1050 (SXGA+), 1440 x 900 (WXGA+), 1600 x 1200 (UXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
RMS rated power	16 W
Number of built-in speakers	2
DVI port	No
BNC input ports	5
USB connector type	USB Type-A, USB Type-B
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	0
Noise level	- dB
Certification	UL/cUL, FCC Part15 class A, AS/NZS CISPR22 class A, CE, GOST-R
Placement	Desktop, Ceiling
Product type	Standard throw projector
Product color	White
Power source	AC
AC input voltage	100 - 240 V
Power consumption (standby)	- W
Operating temperature (T-T)	0 - 45 °C
Sustainability certificates	RoHS

Weight and Dimensions

Depth	396 mm
Width	498 mm
Height	135 mm
Weight	8700 g