Hitachi CP-WU8450 User Manual

12
Setting up
Connecting with your devices (continued)
(continued on next page)
• If an oversized USB storage device blocks the LAN port, use only
the further USB TYPE A port from the LAN port or a USB extension cable to
connect the USB storage device.
NOTE
► Before connecting the projector to a network system be sure
to obtain the consent of the administrator of the network.
► Do not connect the LAN port to any network that might have the excessive voltage.
► The designated USB wireless adapter that is sold as an option is required to use
the wireless network function of this projector. Before connecting the USB wireless
adapter, turn off the power of the projector and disconnect the power cord. Do not
use any extension cable or device when connecting the adapter to the projector.
► Before removing the USB storage device from the port of the projector, be sure to
use the REMOVE USB function on the Thumbnail screen to secure your data (95).
►To connect both the LAN cable and USB device to the projector, use only the
further USB TYPE A port from the LAN port or a LAN cable that is at on the
side where the plug’s wire is visible. Otherwise, both of them cannot be con-
nected correctly, or the wire may break (malfunction).
CAUTION
Computer
Access
point
USB
storage
device
USB
wireless
adapter
(optional)
(
92, 102)
External
device
(
74)
(
74)
(
74)
(
19)
►Heat may build up in the USB wireless adapter, to avoid pos-
sible burns disconnect the projector power cord for 10 minutes before touching
the adapter.
► When using the USB wireless adapter, be sure to connect the adapter to the fur-
ther USB TYPE A port from the LAN port and use the supplied adapter cover (15).
WARNING

Hitachi CP-WU8450 Specifications

General

Matrix size	0.76 \
Matrix type	3-panel (p-Si TFT active)
Native aspect ratio	16:10
Projection distance	1 - 38.3 m
Projection technology	LCD
Contrast ratio (typical)	3000:1
Screen size compatibility	30 - 600 \
Projector native resolution	WUXGA (1920x1200)
Audio input	3
RS-232 ports	1
Zoom capability	Yes
Focal length range	- mm
Lamp type	UHP
Lamp power	330 W
Lamps quantity	1 lamp(s)
Light source type	Lamp
Service life of light source	- h
3D	-
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1360 x 768 (WXGA), 1400 x 1050 (SXGA+), 1440 x 900 (WXGA+), 1600 x 1200 (UXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
RMS rated power	16 W
Number of built-in speakers	2
DVI port	No
BNC input ports	5
USB connector type	USB Type-A, USB Type-B
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	0
Noise level	- dB
Certification	UL/cUL, FCC Part15 class A, AS/NZS CISPR22 class A, CE, GOST-R
Placement	Desktop, Ceiling
Product type	Standard throw projector
Product color	White
Power source	AC
AC input voltage	100 - 240 V
Power consumption (standby)	- W
Operating temperature (T-T)	0 - 45 °C
Sustainability certificates	RoHS

Weight and Dimensions

Depth	396 mm
Width	498 mm
Height	135 mm
Weight	8700 g