3.3.2 Typical Monitoring Displays
VSDA*SAVE
ECOMODE
(Energy Conservation Mode)
“SAVE” is displayed on the monitor
screen.
Displayed when stop is limited for AUTO opera-
tion (standard: no symbol).
INTE :Fixed speed type control (load/unload operation)
AUTO :Fixed speed type control
(AUTO operation *optional)
VSDB :V type control (AUTO function off)
VSDA : V type control (with AUTO function, V type standard)
EXIT :Setting display when capacity control is executed
externally
MR : Multiple unit control connection by communication
control
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
㻞㻜㻜㻥䠋㻜㻠䠋㻝㻟 㻝㻥䠖㻜㻞
㼀㼅㻼㻱 䠖㼂㻿㻰㻭
㻰 㻵 㻿䠊㻼㻾㻱㻿㻿 䠖 㻜䠊㻜 㻜 㼜 㼟 㼕
㻖
㻖
㻾㼁㻺 㻌㻴㻻㼁㻾䠖 㻝 㻞 㻜䡄
㻸㻻㻭㻰 㻌 㻴㻻㼁㻾 䠖 㻡 㻠 䡄
㻸㻻㻭㻰 㼀 㻵 㻹㻱㻿 䠖 㻝 㻞 㻟
㻸㻻㻭㻰 㻾㻭㼀㻱䠖 㻝 㻝䠂
㻸㻻㻭㻰 㼀 㻵 㻹㻱 䠖 㻞 㻠䡏
㼁㻺㻸㻻㻭㻰 㻌 㼀 㻵 㻹㻱 䠖 㻝䡏
㻯㼁㻾㻾㻱㻺㼀 䠖 㻡 㻜䠝
㻲㻾㻱㻽㼁㻱㻺㻯㼅 䠖 㻞 㻟 㻚 㻤䠤䡖
㻻㼁㼀㻼㼁㼀䠖 㻖 㻖 㻚 㻖䡇䠳
㻹㻭㻿 㼀㻱㻾
(10)
(11)
㻞㻜㻜㻥䠋㻜㻠䠋㻝㻟 㻝㻥䠖㻜㻞
㻼㻾㻱㻿㻿㼁㻾㻱
㻵 㻺㼀㻿 㼀㻳䠊㻼 䠖 㻌 㻌 㻞 㻥 㼜 㼟 㼕
䠆
㻻 㻵 㻸 㻌 㻼㻾㻱㻿䠖 㻌 㻌 㻝 㻡 㼜 㼟 㼕
㻯㻸㼀䠊㻼㻾㻱㻿䠖 㻖䠊㻖 㻖 㼜 㼟 㼕
㼀㻱㻹㻼㻱㻾㻭㼀㼁㻾㻱
㻰㻵㻿䠊㼀㻱㻹㻼㻝䠖 㻟㻞㻜䉣
㻰 㻵 㻿䠊㼀㻱㻹㻼 㻞 䠖 㻟
㻝
㻟㻤䉣
㻻 㻵 㻸 㻌 㼀㻱㻹㻼 䠖 㻟 㻣䉣
㻯㻸㼀䠊㼀㻱㻹㻼䠖 㻖㻖㻖䉣
㻞㻺㻰 㻌 㻿㼁㻯㼀䠊㼀䠊䠖 㻜 㻤䉣
㻹㻭 㻵 㻺㼀 㻱 㻺㻭㻺㻯㻱
㻴㻾䠊㼀㻻㻌㻹㻭㻵㻺㼀䠖 㻜㻜㻜㻜䡄
㻺㻱㼄㼀㻌 㻹㻭 㻵㻺㼀䠖 㻖㻖㻖㻖
㻝
(1) Displays current time. Asterisk flashes.
(2) Indicates a capacity control type.
(3) Displays compressor discharge port pressure.
(4) Indicates total running hours (RUN HOUR), total
loaded hours (LOAD HOUR), and total number of
loads (LOAD TIMES.).
Blink asterisk indicates running time is being mea-
sured.
(5) Indicates a percentage of load to unload of the DSP air
compressor (LOAD RATE), For Vtype, the rate is cal-
culated based on only frequency. Indicates “***”,
if PQ wide mode is selected.
When the DSP is operating normally, typical monitoring
displays appear as follows.
M1 Monitoring Display
M2 Monitoring Display
(6) Indicates the amperage current of the main motor
(CURRENT).
(7) Displays an operating frequency of main motor.
(V type only. Fixed speed type displays **.*)
(8) Indicates “*** ” for this air compressor.
(9) Displays master or slave control status when in lead/
lag operation mode.
(10) Displays various pressures and temperatures.
(Asterisk indicates not in use.)
(11) Displays time remaining till next inspection as main-
tenance period and next maintenance period.
Current is an approximate S-phase ampere.
Output is reference value of calculated power.
IMPORTANT
14
3. OPERATING THE DSP [How to Use the Liquid Crystal Display (LCD)]