Honeywell AreaRAE Plus - Page 82

Honeywell AreaRAE Plus

124 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

AreaRAE Plus & AreaRAE Pro User’s Guide

82

4. Place the tip of a flat-blade screwdriver in the slot and gently pry up on the cover, using

the tool for leverage.

5. Once the cover is loose, remove the screwdriver.

6. Lift the lid off, exposing the sensor electrode panel.

Sensor electrode

panel

Table of Contents

Default Chapter3
- Table of Contents3
- Proper Product Disposal at End of Life11
1 Features Comparison12
2 Standard Contents13
3 General Information14
- Key Features15
4 Connections16
5 User Interface17
- Display Overview17
  - Status Indicator Icons17
  - Status Indicator Icons for Instruments Equipped with ISM Radio or Wifi19
- Keys and Interface20
  - Reverse Direction20
- Screen Display for Various Numbers of Active Sensors21
- Glance Mode21
- Menus22
  - Operation Mode Navigation22
6 Wireless Operation23
7 Wireless Control and Submenus24
- ISM Settings25
8 Wifi Settings26
- Setting Wifi Communication Parameters in Prorae Studio II26
9 Relays for Controlling External Equipment28
10 Battery30
- Charging30
- Battery States31
- External Battery Charger31
11 Turning the Arearae Plus/Pro on and off33
- Turning the Arearae Plus/Pro on33
  - Pausing to View Screens During Startup33
- Turning the Arearae Plus/Pro off33
- Testing Alarm Indicators34
- Pump Status34
- Calibration Status34
- Bump Status35
12 Programming36
- Enter Programming in Basic Mode36
- Enter Programming in Advanced Mode37
- Menus and Submenus38
13 User Modes63
- Basic User Mode63
- Advanced User Mode63
14 Policy Enforcement63
- Setting Policy Enforcement63
- Deactivating Policy Enforcement65
15 Calibration and Testing67
- Manual Alarms Test67
- Bump Testing and Calibration67
- Span Calibration70
- Three-Point Calibration for Enhanced Linearity with Extended-Range and Ppb PID Sensors70
16 Datalog Transfer, Monitor Configuration, and Firmware Upgrades Via Computer75
- Downloading Datalogs and Performing PC-Based Instrument Configuration and Firmware Upgrades75
17 Maintenance76
- Removing/Installing the Rubber Boot76
- Replacing the External Filter76
- Removing/Cleaning/Replacing Sensor Modules77
- Cleaning or Replacing the PID78
  - Cleaning or Replacing the 4R+ PID79
  - Cleaning or Replacing the 7R+ PID81
- Replacing the Sensor Compartment Cover86
- Battery Removal/Replacement86
- Alkaline Battery Pack88
- Raemet Meteorological Sensor (Optional)92
- Antenna Installation93
- Replacing the Pump94
18 Alarms Overview96
- Alarm Signals96
- Changing the Alarm Mode96
19 Diagnostic Mode97
- Enter Diagnostic Mode97
- Adjusting Alarm Leds & Buzzer97
- Adjusting LCD Contrast97
- Pump Stall Threshold Adjustment97
- Alarm Signal Summary103
  - Hygiene Mode103
  - General Alarms104
20 Troubleshooting105
21 Specifications106
22 Technical Support122
23 RAE Systems by Honeywell Contacts123

Other manuals for Honeywell AreaRAE Plus

User Manual145 pages

Related product manuals

Preview: Honeywell AreaRAE Pro

Honeywell AreaRAE Pro

Preview: Honeywell C7061 A

Honeywell C7061 A

Preview: Honeywell Activ8 PIR

Honeywell Activ8 PIR

Preview: Honeywell Viewguard DUAL AM FAI

Honeywell Viewguard DUAL AM FAI

Honeywell FIRE-LITE ALARMS H365

Preview: Fire-Lite Alarms D365PL

Fire-Lite Alarms D365PL

FIRE-LITE ALARMS SD365CO

Preview: Viewguard DUAL AM BUS-2/BUS-1

Viewguard DUAL AM BUS-2/BUS-1

Preview: Honeywell 5800CO

Honeywell 5800CO

Preview: Honeywell 5800PIR

Honeywell 5800PIR

Preview: Honeywell FlexGuard FG-1625

Honeywell FlexGuard FG-1625

Preview: Miller TurboLite Series

Miller TurboLite Series