What to do if Honeywell QuantumT MS3580 powers up but doesn't communicate with host?
If your Honeywell Scanner powers up and scans but doesn't communicate correctly with the host, ensure the baud rate and parity of both the scanner and the host match. Also, verify the cable is connected to the correct com port.
What to do if Honeywell Scanner powers up but does not scan or beep?
If your Honeywell Scanner powers up but doesn't scan or beep, check if it has been configured for a character length lock or a minimum length criteria. Verify that the bar code being scanned meets these criteria.
Why Honeywell Scanner powers up but does not beep?
If your Honeywell Scanner powers up but does not beep, it may be because the beeper is disabled. Enable the beeper. Alternatively, no tone may be selected, so select a tone.
Why Honeywell QuantumT MS3580 Scanner scans the barcode but no data?
If your Honeywell Scanner scans the bar code but there is no data, ensure that the proper PC type (i.e., AT, PS2, or XT) is selected.
What to do if Honeywell Scanner scans but data is not correct?
If your Honeywell Scanner scans but the data is not correct, verify that the correct country code and data formatting are selected, and adjust the intercharacter delay.
Why Honeywell QuantumT MS3580 beeps at some barcodes and not others?
If your Honeywell Scanner beeps at some bar codes but not others of the same symbology, check if check digits are set properly, as the scanner may not be configured correctly for the type of bar code.
Why Honeywell QuantumT MS3580 Scanner has multiple scans on same symbol?
If your Honeywell Scanner produces multiple scans upon presentation of the same symbol, adjust the same symbol timeout for a longer time increment, as the timeout may be set too short.
How to fix Honeywell QuantumT MS3580 not transmitting each character?
If your Honeywell Scanner is not transmitting each character, adjust whether the F0 break is transmitted. It may be necessary to try both settings.
Why Honeywell QuantumT MS3580 is dropping characters?
If characters are being dropped by your Honeywell Scanner, add some intercharacter delay to the transmitted output by using the MetroSelect Configuration Guide (MLPN 00-02407).
Why is Honeywell QuantumT MS3580 Scanner transmitting incorrect data to the host?
If the data transmitted from your Honeywell Scanner to the host is incorrect, ensure that the scanner is connected to the proper host port, as the scanner’s data format may not match what the host requires.
Details the basic kit components and optional accessories available for the MS3580 scanner.
Offers guidance on cleaning and maintaining the MS3580 scanner to ensure optimal performance.
Guides the user through connecting the scanner using RS232, TTL, Light Pen, or Laser emulation interfaces.
Details the installation procedure for the MS3580 scanner using the RS485 communication interface.
Explains how to install the scanner for use with a keyboard wedge interface.
Provides instructions for setting up the scanner in a stand-alone keyboard configuration.
Covers the installation process for connecting the MS3580 scanner via USB.
Lists the LED and audible indicators that signal scanner malfunctions and their solutions.
Highlights critical safety precautions, particularly regarding laser exposure and proper usage.
General| Scan Technology | Laser |
|---|---|
| Interface | USB, RS-232, Keyboard Wedge |
| Reading Distance | 40 mm - 216 mm |
| Weight | 170 g |
| Power Supply | 5 VDC ± 0.25 V |
| Light Source | 650 nm visible laser diode |
| Decode Capability | 1D barcodes |
| Depth of Field | 40 mm - 216 mm (1.5" - 8.5") for 0.33 mm (13 mil) bar codes |
| Field of View | 42° |
| Operating Temperature | 32°F to 122°F (0°C to 50°C) |
| Storage Temperature | -40°C to 60°C (-40°F to 140°F) |
| Humidity | 5% to 95% (non-condensing) |
| Voltage Range | 5 VDC ± 0.25 V |
| Supported Symbologies | UPC/EAN, Code 39, Code 128, RSS |
To Next Page