Honeywell ScanPal EDA50K User Manual

1. Features of ScanPal EDA50 Enterprise Hybrid Device
ScanPal EDA50 Enterprise Hybrid Device User Guide 15
Battery maintenance recommendations and safety
protection measures
• Fully charge the battery before use. The battery is only partly charged when
initially shipped.
• Refer to the chapter "charging" to get the right process for battery charging.
Using the battery for other devices may cause damages on the device or
the battery.
• Avoid dropping the battery or the terminal. If you suspect that a battery or
terminal fails, send it to Honeywell service center for verification.
• This battery should only be replaced by another Honeywell BAT-EDA50
battery. These batteries have been tested and meet the appropriate safety
standards.
• Before recycling the battery, cover the contacts with insulation tape.
• Do not modify the battery or attempt to insert foreign objects into the
battery.
• Do not solder directly to the battery poles.
• Do not short connect the battery and put the battery away from metal
objects.
• Do not drop or mechanically shock or extrude the battery.
• Do not disassemble or open the battery. Do not crush, bend or deform the
battery; Do not puncture, shred or burn the battery.
• Do not immerse the battery in water.
• Avoid extreme temperature conditions as found on the dash of a car in the
sun or near a heat source such as a stove or open flame. After extreme
low or high temperature exposure, allow the terminal and battery to come to
room temperature before charging
Charging While in Use
Avoid charging the terminal continuously while in use to maximize battery cycle
life. Battery health is maximized when the terminal is turned off or in the
Suspend state during charging.
Suspend (or “sleep”) is an ultra-low-power state where the main processor and
display are powered off to minimize power consumption. Under factory settings,
the terminal automatically enters the Suspend state after a brief period of non-
use. However, certain software applications or configuration settings can keep
the terminal awake.
If the terminal does not Suspend within the expected time limit, do not leave the
terminal in the charger. Check application settings. Update to the latest system
software.

Honeywell ScanPal EDA50K Specifications

General

HDD capacity	128 GB
Audio (L/R) in	1
Composite video in	0
DVI-D ports quantity	5
DVI-I ports quantity	4
USB 2.0 ports quantity	8
Ethernet LAN (RJ-45) ports	-
Component video (YPbPr/YCbCr) in	7.5
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	1.9
Display diagonal	4 \
External display	No
Touch technology	Multi-touch
Touchscreen type	Capacitive
Display resolution	480 x 800 pixels
Flash memory	16 GB
Internal memory	0.002 GB
Compatible memory cards	MicroSDHC
Maximum memory card size	32 GB
Processor family	Snapdragon
Processor frequency	1.2 GHz
Processor manufacturer	Qualcomm
Operating system version	4.4
Operating system installed	Android
Data network	EDGE, GSM, LTE, WCDMA
Wi-Fi standards	802.11a, 802.11b, 802.11g
Bluetooth version	4.0
GSM bands supported	900, 1800 MHz
Security algorithms	802.1x RADIUS, AES, EAP-TLS, EAP-TTLS, TKIP, WEP, WPA, WPA-PSK, WPA2
WCDMA bands supported	900, 2100 MHz
Rear camera resolution (numeric)	5 MP
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 90 %
Battery voltage	3.8 V
Battery capacity	4000 mAh
Battery life (max)	12 h
AC adapter output current	2 A
AC adapter output voltage	5 V
Battery recharge time (off)	4 h
Product color	Black
Keyboard layout	Alphanumeric
International Protection (IP) code	IP54

Weight and Dimensions

Depth	24.5 mm
Width	73 mm
Height	164 mm
Weight	300 g