Honeywell ScanPal EDA50K User Manual

7. Management and maintenance
70 ScanPal EDA50 Enterprise Hybrid Device User Guide
Restore factory settings
If the terminal appears to be locked, try a cold boot. If resetting is invalid, try to
restore factory settings, restart the terminal to make it work again and do
troubleshooting later.
Warning: This action will clear all data in the terminal, including all
applications and data, but excluding data stored in flash memory or
external storage device.
1. Tap All Applications > Settings.
2. Tap Backup & Reset.
3. Tap Restore Factory Settings.
4. Tap Reset the Phone.
5. EDA50 will restart and automatically clear user data.
Cleaning the terminal
In order to ensure the terminal in good working condition, you need to clean the
scan window, camera and touch screen. Based on the environmental conditions
where the terminal is being used, clean these parts at regular intervals. Use a
clean, soft cloth dampened with the following solvents for the cleaning, and
quickly wipe it with another piece of clean, soft cloth.
• Acetic acid (10% soluble in water)
• Ethanol (10% soluble in water)
• Neutral soap solution
Warnings: this product includes non user-serviceable parts inside.
Disassembling the product may prevent warranty and cause internal
damages to the product.
Note: We advise you not to open the battery cover or remove the battery,
so as to avoid the liquid flowing into the internal part of the terminal from
the SIM card and SD card interface.
1. Press the power key to enter standby mode.
2. Dip a clean cloth in detergent, then wrung out excessive water.
3. Wipe the scanning window, camera and flash area, avoiding touching these
areas with hard objects or abrasive materials.
4. Dry the cleaned area.
5. Make sure the terminal is fully dry before using it again.

Honeywell ScanPal EDA50K Specifications

General

HDD capacity	128 GB
Audio (L/R) in	1
Composite video in	0
DVI-D ports quantity	5
DVI-I ports quantity	4
USB 2.0 ports quantity	8
Ethernet LAN (RJ-45) ports	-
Component video (YPbPr/YCbCr) in	7.5
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	1.9
Display diagonal	4 \
External display	No
Touch technology	Multi-touch
Touchscreen type	Capacitive
Display resolution	480 x 800 pixels
Flash memory	16 GB
Internal memory	0.002 GB
Compatible memory cards	MicroSDHC
Maximum memory card size	32 GB
Processor family	Snapdragon
Processor frequency	1.2 GHz
Processor manufacturer	Qualcomm
Operating system version	4.4
Operating system installed	Android
Data network	EDGE, GSM, LTE, WCDMA
Wi-Fi standards	802.11a, 802.11b, 802.11g
Bluetooth version	4.0
GSM bands supported	900, 1800 MHz
Security algorithms	802.1x RADIUS, AES, EAP-TLS, EAP-TTLS, TKIP, WEP, WPA, WPA-PSK, WPA2
WCDMA bands supported	900, 2100 MHz
Rear camera resolution (numeric)	5 MP
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 90 %
Battery voltage	3.8 V
Battery capacity	4000 mAh
Battery life (max)	12 h
AC adapter output current	2 A
AC adapter output voltage	5 V
Battery recharge time (off)	4 h
Product color	Black
Keyboard layout	Alphanumeric
International Protection (IP) code	IP54

Weight and Dimensions

Depth	24.5 mm
Width	73 mm
Height	164 mm
Weight	300 g