Honeywell VISTA Series - Power Management Features

HoneywellVISTASeriesProductsUserManual

16
Thisoptionisusedtosettheextentofmatchingbetweenaninputfi ngerprintandthatstoredintem plates.For
details, see 2.3MatchThreshold.
7)1:1Lvl
ThisoptionisusedtosettheextentofmatchingbetweenaninputID/fingerprintandthatstoredintemplates
intheIDandfingerprintidentificationmode.Fordetails,see 2.3MatchThreshold.
8)ExtFPDevê
Ifyouselect"Y",youcaninstallanexternalfingerprintsensorthroughtheUSBi nterfaceandusethisexternal
sensortogetherwiththefingerprintreaderaccompaniedwiththeFRT.Ifyouselect"N",youcannotinstallany
externalfingerprintsensor.Fordetails,seeAppendixExternalConnectionwiththeFingerprintReader.
9)FirmwareUpd
Youcanselect"FirmwareUpd"toupgradethefirmwareofanFRTthroughtheupgradefilesintheUSBpen
drive.
Note:Ifyouneedfirmwareupgradefiles,pleasecontactourtechnicalsupportengineers.Generallyitisnot
recommendedtoupgradethefirmware.
10)Buzzer
Thisparameterisusedtosetwhethertoplayvoicepromptsduringtheoperati onoftheterminal.Select"ON"
toenablethevoiceprompt,andselect"OFF"tomute.
11)AntiPassbackê
Thisoptionhasfourvalues:None,Exit,EntryandEntryandExit.Fordetails,seeAppendixAntiPassback.
12) AlgVer
Thisoptionisusedtosettheversionnum berofthefingerprintal gorithm.Select9toadoptalgorithmversion
9.0 and10toadopt algorithmversion10.0. Please select the algorithmversion with caution because the
fingerprinttemplatesofthesetwoalgorithmversionsareincompatible.
Note:someofthedevicewillbepromptedtoremovetheuserinformationandattendancedatawhenchange
thealgorithm.Soweproposedtobackupuserinformationandattendancedatabeforechangethealgorithm.
Note:
1.Theoptions
TwoSensor
and
UpdFirmware
areavailableonlyontheUSBcapableFRTs.
2.Theoption
CardOnly
isavailableonlyontheMifarecardcapabl eorIDcardcapableFRTs.
3.Theoptions
R.cardOnly
and
FPCardKey
areavailableonlyontheMifarecardcapableFRTs.
4.Theoptions
RemoteVerify
and
ServerIP
areavailableonlyontheRIScapableFRTs.
5.Theoptions
KeypadTone
and
AdjVOL
areavailableonlyontheFRTsthatadopttheURUsensor.
6.Theoption
Work Code
isavailableonlyontheFRTsthatsupporttheworkcodefeature.
7.Theoption
ImdtPrt
isavailableonlyontheprintcapableFRTs.
8.Theoption
AntiPassback
isavailableonlyontheantipassbackcapableFRT s.
4.2PowerManagement
ê
Through power management, you can set the timing poweron/shutdown, poweron/shutdown time, lock
powerkey,andtimingstateswitching.
4.2.1PowerSettings
PressMenutoaccesssystemmenu.Sel ectOptions→PowerMgttodisplaythefollowinginterface.
Power Mgt ▼
►PowerOn N
Sleep N
Idle SLP
IdleTime 0