HP 209A - Page 5

Table of Contents
Model209A
TABLE OF CONTENTS
APPENDICES
A. CODE LIST
OF MANUFACTURERS
B. SALES AND SERVICE OFFICES
C. MANUAL BACKDATING CHANGES
Section Page
VI REPLACEABLE PARTS
6-1
6-1. Introduction 6-1
6-4. Ordering Information 6-1
6-6. Non-Listed Parts 6-1
Section Page
VII CIRCUIT DIAGRAMS
7-1
7-1. Introduction 7-1
7-3. Schematic Diagrams 7-1
7-5. Component Location Diagrams 7-1
Page
5-23.
5-26.
5-28.
5-29.
5-30.
Section
V MAINTENANCE
(Cont'd)
5-8. Distortion Check 5-3
5-9.
Output Voltage and Impedance
Check (Sine Wave) 5-4
5-10.
Output Control Check
(Sine Wave) 5-4
5-11. Balance Check (Sine Wave) 5-4
5-12.
Output Voltage Check
(Square Wave) 5-4
5-13. Rise Time Check
(Square Wave) 5-5
5-14.
Symmetry Check
(Square Wave) 5-5
5-15. Sync
Output Check 5-5
5-16.
Sync Input Check 5-5
5
-1 7. Cover Removal . . . . . . . . . . . . . . . . . 5-6
5-22. Adjustment and Calibration
Procedure 5-6
Introduction 5-6
Power Supply 5-6
Bias Adjustment 5-6
AGC Adjustment 5-6
AGC
and Frequency
Adjustment 5-6
5-31. High Frequency Adjustment 5-7
5-32. Distortion Adjustment 5-7
5-33.
Symmetry Adjustment 5-7
5-34.
Factory Selected Components 5-7
5-36. Troubleshooting Procedures 5-8
5-37. Front Panel Procedure 5-8
5-40. Detailed Circuit
Troubleshooting 5-8
Section Page
V MAINTENANCE 5-1
5-1. Introduction
5-1
5-4. Performance Checks 5-1
5-6. Dial Accuracy Check
5-1
5-7. Flatness Check 5-1
Section Page
I GENERAL INFORMATION
1-1
1-1. Introduction 1-1
1-3. Specifications 1-1
1-5. Description 1-1
1-10. Instrument/Manual Identification .. 1-1
Section Page
II INSTALLATION
2-1
2-1. Introduction 2-1
2-3. Initial Inspection 2-1
2-5. Power Requirements 2-1
2-7. Grounding Requirements 2-1
2-10. Installation 2-1
2-12. Bench Mounting 2-1
2-14. Rack Mounting 2-1
2-16. Combination Mounting 2-1
2-18. Repackaging for Shipment 2-1
Section Page
III OPERATING INSTRUCTIONS
3-1
3-1. Introduction 3-1
3-3. Turn On Procedure 3-1
3-5. Operating Considerations 3-1
3-6. Floating Output 3-1
3-8. Balance 3-1
3-10. Synchronization 3-1
3-13.. Low Distortion 3-1
Section Page
IV THEORY
OF OPERATION 4-1
4-1. Introduction 4-1
4-4. Block Diagram Description , 4-1
4-5. Bridge and Amplifier 4-1
4-9. Peak Comparator and AGC _ 4-1
4-13. Buffer Amplifier 4-2
4-15. Sine-Square Converter 4-2
4-17. Detailed Circuit Description 4-2
4-25. Power Supply 4-2
iii
www.HPARCHIVE.com