To Next PageTo Next Page
Need help?Do you have a question about the HP ProLiant ML10 and is the answer not in the manual?
General| Memory Slots | 4 |
|---|---|
| Form Factor | Tower |
| Processor | Intel Xeon E3-1200 v3 |
| Memory | Up to 32 GB |
| Drive Bays | 4 LFF |
| Power Supply | 300W |
| Chipset | Intel C222 |
| Expansion Slots | 1 PCIe 3.0 x16, 1 PCIe 2.0 x1 |
| Operating System Support | Windows Server, Red Hat Enterprise Linux, SUSE Linux Enterprise Server, VMware ESXi |
| RAID Support | Integrated SATA RAID controller (Intel Rapid Storage Controller); optional HP Smart Array controllers |
Identifies and describes the front panel components of the server.
Details the LEDs and buttons located on the front panel of the server.
Lists and describes the components found on the rear panel of the server.
Details the LEDs and buttons located on the rear panel of the server.
Identifies and describes the components on the server's system board.
Illustrates the location and numbering of the DIMM slots on the system board.
Explains the function and configuration of the system maintenance switch.
Describes the Non-Maskable Interrupt (NMI) feature for system diagnostics and crash dumps.
Identifies the locations of the system and processor fans within the server.
Step-by-step instructions for powering on the server.
Procedures for safely shutting down and powering off the server.
Instructions on how to remove the server's access panel for internal access.
Steps to remove the front bezel to access drive bays and media bays.
Instructions for reinstalling the front bezel after component access.
Steps for reinstalling the server's access panel.
Information on HP Care Pack services for installation and support.
Guidance on selecting a suitable location for server installation.
Specifies the necessary clearance for proper server ventilation.
Outlines the acceptable operating temperature ranges for the server.
Details the electrical power specifications and installation guidelines.
Explains the necessary electrical grounding procedures for safety and operation.
Lists the items typically found in the server shipping carton.
General instructions for installing additional hardware options.
Steps to set up the server in a tower configuration.
Instructions for powering on and initial configuration of the server.
Guidance on installing a supported operating system onto the server.
Information on how to register the server for enhanced support.
General advice for installing multiple hardware options efficiently.
Information on where to find detailed product specifications and compatibility.
Guidelines for installing new drives in the server.
Step-by-step instructions for installing the drive enablement hardware.
Detailed steps for installing the 3 Large Form Factor (LFF) drive enablement kit.
Instructions for installing an optical drive into the server.
Explains how to identify DIMM characteristics from its label and specifications.
Differentiates between single-rank and dual-rank DIMMs and their implications.
Describes how the server's memory is organized into channels and slots.
Guidance on optimizing memory availability and error correction settings.
Rules and best practices for populating DIMM slots with memory modules.
Step-by-step instructions for installing a DIMM into a memory slot.
General guide to installing expansion boards in PCIe slots.
Instructions for removing slot covers to install expansion boards.
Steps for installing an expansion board into a PCIe slot.
Illustrates the SATA and power cable connections for server drives.
Shows how to connect cables for the front panel I/O assembly.
Details the SATA and power cable connections for the optical drive.
Describes the connection for the ambient temperature sensor.
Illustrates how to connect system and processor fans.
Shows the power cable connections for the server's power supply.
Overview of software tools for server configuration.
Details the HP ROM-Based Setup Utility for system configuration.
Instructions on how to navigate and use the RBSU utility.
Explains the automatic server configuration process during initial boot.
Information about the Array Configuration Utility for storage management.
Steps to re-enter serial number and product ID after system board replacement.
Overview of various management tools for the server.
Explains the Automatic Server Recovery feature for system restarts.
Information about the ROMPaq utility for system firmware upgrades.
Overview of the iLO subsystem for remote server management.
Details the USB 2.0 and legacy USB support provided by the server.
Information on diagnostic tools for server hardware and software.
Describes the HP Insight Diagnostics survey for gathering system information.
Explains the Integrated Management Log (IML) for recording system events.
Information on tools for remote server support and analysis.
Details the HP Insight Remote Support software for monitoring and service.
Guidance on maintaining the server with updated drivers and software.
Information on obtaining and installing necessary device drivers.
Information on supported operating systems for the server.
Describes the HP Smart Update Manager for firmware and software deployment.
Information on HP's notification service for product changes.
Details HP Care Pack Services for extended support and warranty.
Links to troubleshooting guides for older HP ProLiant server models.
Instructions for replacing the system battery that powers the real-time clock.
Reference to safety and regulatory compliance information for HP products.
Information regarding regulatory markings for specific regions.
Declaration regarding hazardous substance content for Turkey.
Declaration regarding hazardous substance content for Ukraine.
Links to warranty information for various HP server and networking products.
Precautions to prevent damage from static electricity when handling components.
Methods for properly grounding yourself to prevent ESD damage.
Details the server's environmental operating and non-operating conditions.
Provides physical dimensions and weight specifications for the server.
Lists the input voltage, frequency, and current ratings for the power supply.
Information to gather before contacting HP support for assistance.
Contact details and websites for HP technical support and assistance.
Information on HP's Customer Self Repair program for parts replacement.
A list of common acronyms and their full definitions used in the document.
