What does an Abnormal Residual Current mean on my Huawei SUN2000-(2KTL-6KTL)-L1?
D
Deanna PooleSep 3, 2025
If your Huawei Inverter is reporting an abnormal residual current, it suggests that the insulation impedance on the input side to PE has decreased during operation. Here’s how to address it:
1. If the alarm is occasional, the external circuit may be temporarily abnormal. The inverter should recover automatically once the fault clears.
2. If the alarm occurs frequently or persists, check whether the impedance between the PV string and the ground is too low.
M
Michele BurchSep 1, 2025
How to fix Low Insulation Resistance on a Huawei Inverter?
A
Anthony JordanSep 1, 2025
If your Huawei Inverter is showing a low insulation resistance warning, take these steps:
1. Check the output impedance of the PV array to ground for any short circuits or insulation issues, and rectify them.
2. Ensure the PE cable of the inverter is correctly connected.
3. If the impedance is lower than the protection threshold on rainy or cloudy days, configure Insulation resistance protection using the mobile app, SmartLogger, or NMS.
M
Michael LopezAug 31, 2025
What to do if my Huawei SUN2000-(2KTL-6KTL)-L1 says 'String Reversed'?
J
James BennettAug 31, 2025
If your Huawei Inverter indicates a reversed string, it means the PV string is connected with incorrect polarity. To fix this, wait until the PV string current decreases below 0.5 A, set the DC switch to OFF, and then correct the PV string polarity.
T
Tyler CraigAug 29, 2025
What does it mean when my Huawei SUN2000-(2KTL-6KTL)-L1 displays a Grid Overfrequency error?
K
karen49Aug 29, 2025
If your Huawei Inverter is showing a grid overfrequency alarm, it indicates a power grid exception where the actual frequency is higher than the standard requirement. Here's what you can do:
1. If the alarm occurs occasionally, it might be a temporary grid issue, and the inverter should recover automatically.
2. If the alarm occurs frequently, check if the power grid frequency is within the allowed range. If it's not, contact your local power operator.
V
Victoria WeissAug 28, 2025
How to troubleshoot a High String Input Voltage error on a Huawei SUN2000-(2KTL-6KTL)-L1 Inverter?
R
Robin WillisAug 28, 2025
A high string input voltage on your Huawei Inverter typically means the PV array isn't properly connected. Too many PV modules might be connected in series, causing the open-circuit voltage to exceed the inverter's maximum operating voltage. Check the serial connections of the PV string to ensure the open-circuit voltage doesn't exceed the maximum operating voltage. Once corrected, the alarm should disappear.
D
diazemmaAug 26, 2025
What to do if my Huawei Inverter reports a Grid Undervoltage issue?
M
Megan StuartAug 27, 2025
If your Huawei Inverter displays a grid undervoltage error, consider the following:
1. If the alarm is infrequent, the power grid may be temporarily abnormal. The inverter should automatically recover when the grid normalizes.
2. If the alarm is frequent, verify that the power grid voltage is within the allowed range. If it's not, contact your local power operator. If it is, you may need to adjust the grid undervoltage protection threshold using the mobile app, SmartLogger, or network management system (NMS), but only with the consent of the local power operator.
T
Tyler DonaldsonAug 25, 2025
What to do when my Huawei SUN2000-(2KTL-6KTL)-L1 shows a Grid Overvoltage error?
M
Michael GrayAug 25, 2025
If your Huawei Inverter is showing a grid overvoltage alarm, here's what to do:
1. If the alarm appears occasionally, it might be due to a temporary issue with the power grid. The inverter should automatically recover once the grid returns to normal.
2. If the alarm occurs frequently, check if the power grid voltage is within the acceptable range. If it's not, contact your local power operator.
J
Jacob TaylorAug 23, 2025
How to fix a DC Arc Fault on a Huawei SUN2000-(2KTL-6KTL)-L1 Inverter?
C
Cory MartinAug 23, 2025
If you're encountering a DC Arc Fault with your Huawei Inverter, it could be due to arcing or poor contact in the PV string power cables. Check the string cables to ensure they are properly connected and not arcing.
Huawei SUN2000-(2KTL-6KTL)-L1 Specifications
General
Output Frequency
50 Hz / 60 Hz
Cooling
Natural Convection
Protection Degree
IP65
Max. Apparent AC Power
2, 200 VA / 3, 300 VA / 4, 000 VA / 4, 400 VA / 5, 500 VA / 6, 600 VA
Max Output Power
2, 200 W / 3, 300 W / 4, 000 W / 4, 400 W / 5, 500 W / 6, 600 W
Provides essential safety instructions for equipment installation, operation, and maintenance, emphasizing adherence to warnings and local regulations.
To Next Page
General
