To Next Page

To Previous Page

227

Change the Engine Source Assignments

The instructions in this section are optional and allow you to change which engine is assigned as the Engine 1, Engine 2, or Engine

3 source in the control head.

1. Press the HOME key.

2. Select Settings.

3. Select Network.

4. Select Data Sources.

5. Under Engine Data, select Engine 1, Engine 2, or Engine 3.

6. Turn oﬀ Auto-Conﬁgure.

7. Select an Engine from the list.

Engine 1 Source Auto-Configured

When Auto-

Configure is

turned on, the

control head

assigns numbers

to each engine

automatically.

Instance 0 =

Engine 1 Source

Engine (1) is selected

NMEA 2000 Setup

Warnings2
- Table of Contents4
Introduction6
Getting Started7
Touch Screen Overview13
ONIX Touch Screen and Keypad14
ION Touch Screen and Keypad16
ONIX Control Head18
- Menu Key19
- Arrow Keys19
ION Control Head20
- Arrow Keys21
- Menu Key21
- Exit Key21
The Home Screen23
The Menu System28
Views34
- Edit the On-Screen View38
- The View Options Menu43
- Create a New View45
- Set up an Instrument View49
Chart Overview51
- Map Source52
- Navigation Alarms Overview60
- Arrival Alarm61
- Man Overboard (MOB)65
- Customize the Chart View66
- Open the Chart Preferences Menu66
- Change the Chart View Overlays70
- Chart and Radar71
- Change the Chart Mode72
Introduction to Navigation74
Navigation Menu Overview75
- Navigation X-Press Menu75
- Mark Menu76
- Go to Menu76
- Info Menu78
- Cursor Menu80
Waypoints81
Routes86
Search93
Tracks95
Manage Your Navigation Data98
- Manage Waypoints99
- Manage Routes102
- Manage Tracks104
- Manage Groups107
- Delete All Navigation Data108
- Import/Export Navigation Data108
Autochart LIVE Overview109
- Plan Your Map109
- Prepare the Control Head for Mapping110
- Record Your Custom Map113
- Correct Data115
- Display/Hide Your Custom Map116
- Adjust the Map Display Settings117
Mosaic Overview120
- For Best Performance120
- Open the Mosaic Menu120
- Customize the Mosaic Display122
Autopilot Overview127
Radar Overview129
- Radar Alarms130
- Radar Transmission Settings133
- Adjust the Transmission Range134
- Customize the Radar View135
- Open the Radar Preferences Menu135
- Change the Radar View Overlays137
- Adjust Radar Signal Settings140
- Ebl/Vrm141
- Navigation in Radar View143
AIS and MARPA145
- AIS and MARPA Alarms145
- AIS and MARPA Display Settings147
AIS Overview149
MARPA Targets156
Sonar Overview161
- Sonar Setup163
- Sonar Alarms164
Sonar Overview165
- Customize the 2D Sonar View166
- Open the Sonar Preferences Menu166
- Change the 2D Sonar View Overlays171
- Adjust 2D Sonar Display Settings172
Side Imaging Overview175
- Customize the Side Imaging View177
- Open the Side Imaging Preferences Menu177
- Change the Side Imaging View Overlays179
- Adjust Side Imaging Display Settings180
Down Imaging Overview182
- Customize the down Imaging View183
- Open the down Imaging Preferences Menu183
- Change the down Imaging View Overlays185
- Adjust down Imaging Display Settings186
Use Cursor and Zoom in Sonar Views (2D, SI, DI)188
Navigation in Sonar Views (2D, SI, DI)190
Sonar Recording193
Images Tool194
Video View200
Internet Tool203
Installation Information206
- Set up Wireless207
- Set up or Change Transducer Settings (Optional)211
- Configure Radar (Installation and Repair Only)214
- Configure the Control Head218
  - System Info218
  - Nmea 0183220
- Set up Anmea 2000 Network222
- Set up Your Humminbird Network231
- Change the Network Name239
Manage Your Control Head241
Update Software243
Statements and Acknowledgements247
Contact Humminbird252

Networking	Ethernet
Waterproof Rating	IPX7
Waypoints	3000
Power Output	500W (RMS)
Frequency	50/83/200 kHz
GPS Receiver	Internal

Humminbird ONIX Opeartion Manual

Table of Contents

Other manuals for Humminbird ONIX

Questions and Answers:

Humminbird ONIX Specifications

Related product manuals