Need help?Do you have a question about the Hunter X-Core XC-801i-E and is the answer not in the manual?
General| Model | XC-801i-E |
|---|---|
| Number of Zones | 8 |
| Wi-Fi Connectivity | No |
| Rain Sensor Compatibility | Yes |
| Operating Voltage | 24 VAC |
| Watering Duration | 1 minute to 4 hours |
| Cycle and Soak | Yes |
| Rain Delay | Yes, up to 7 days |
| Manual Watering | Yes |
| User Interface | LCD |
| Mounting | Wall Mount |
| Water Budget | 10% to 150% |
| Programs | 3 independent programs (A, B, C) with up to 4 start times each |
Details the various icons and indicators on the controller's liquid crystal display for status and programming.
Describes the electrical connections and components housed within the controller's wiring compartment.
Explains the function of each button on the controller's interface for navigation and operation.
Outlines the different positions on the controller's dial and their corresponding functions for programming.
Details the AC power transformer used with the indoor model of the X-Core controller.
Provides instructions for connecting AC power to outdoor models of the X-Core controller safely.
Explains how to test the functionality of a connected rain sensor for proper operation.
Details how to temporarily disable the rain sensor's function for manual control.
Guides on connecting the Solar Sync sensor wires to the controller's terminals.
Instructions for connecting the Wireless Solar Sync receiver to the controller.
Explains how to configure Region and Water Adjustment settings for Solar Sync.
Provides a guide to determine the correct regional setting based on ET and temperature data.
Describes how to adjust the seasonal watering based on sensor input, from 1 to 10.
Outlines the process to disconnect and remove the Solar Sync sensor from the controller.
Details how to calibrate the Solar Sync sensor for optimal performance based on site conditions.
Explains compatibility and connection of Hunter Remote Controls to the X-Core controller.
Provides steps for installing the SmartPort connector for remote control functionality.
Guides on how to set the current year, month, day, and time on the controller.
Details how to set up to four daily start times for each watering program.
Describes the procedure to remove or disable a previously set program start time.
Explains how to assign watering duration for each station, from 1 minute to 4 hours.
Covers how to define the watering days using various methods like specific days or intervals.
Instructions on choosing individual days of the week for watering.
How to set watering schedules based on odd or even numbered days of the month.
Guides on setting watering to occur at specified intervals between 1 to 31 days.
Allows designating specific days of the week as non-watering days.
Explains how to enable the controller for automatic watering based on programmed schedules.
Details how to temporarily stop all watering operations by turning the dial to System Off.
Allows setting a temporary pause for watering for a period of 1 to 7 days.
How to globally adjust watering run times by a percentage based on seasonal needs.
Instructions for initiating watering for a single station manually.
How to run all stations manually or advance through stations during a manual cycle.
Enables disabling watering for specific stations when a sensor input is received.
Runs a test cycle for each station to verify operation and watering times.
A diagnostic tool to quickly identify potential wiring problems within the controller.
Features for saving and retrieving programmed watering schedules from memory.
Allows setting a delay period between the operation of consecutive watering stations.
Procedure to reset the controller to factory defaults, erasing all programmed data.
Enhances watering by splitting run times into cycles and soak periods to prevent runoff.
How to navigate to the Cycle and Soak programming menus.
Defines the duration of each watering cycle for a station.
Procedure to access the Soak time settings after setting cycle times.
Sets the duration for water absorption between watering cycles for a station.
Lists the functional capabilities and operational parameters of the X-Core controller.
Details the electrical requirements, outputs, and protection features of the controller.
Defines the meaning of various symbols used throughout the manual.
Outlines compliance with FCC regulations for digital devices, including interference guidelines.
To Next Page
