What to do if my Hunter X-CORE XC-2 Controller display shows “ERR” with number ERR message?
If the display on your Hunter Controller shows “ERR” followed by a number, it typically indicates a short in the field wiring or a faulty solenoid. You should check the field wiring and valve solenoid to identify and fix the problem.
What to do if my Hunter X-CORE XC-2 Controller display shows P “ERR”?
If the display on your Hunter Controller shows P “ERR”, this indicates a short in the P/MV wiring or solenoid. Check the wiring and solenoid at the P/MV, and refer to the specifications for the Pump Start Relay.
How to fix a frozen or garbled display on my Hunter Controller?
If your Hunter Controller's display is frozen or garbled, it is likely due to a power surge. Try resetting the controller to resolve the issue.
What does it mean if my Hunter Controller display shows SP “ERR”?
If the display on your Hunter Controller shows SP “ERR”, it means that electrical noise is present near the connection to the remote or another SmartPort device. Move the connections away from sources of electrical noise, and verify that the controller has been wired correctly.
What to do if my Hunter X-CORE XC-2 seems to water continuously?
If your Hunter Controller is constantly watering, the issue might be due to having too many START TIMES programmed. Try removing any unnecessary Start Times to resolve this.
What to do if my Hunter X-CORE XC-2 Controller display shows WATERING BUT NO WATERING IS OCCURRING?
If your Hunter Controller display indicates watering but no actual watering is happening, there may be a problem in the field wiring. Inspect the field wiring using a voltmeter, check the valve solenoid(s), and ensure that the water source is open.
Why is my Hunter X-CORE XC-2 Controller rain sensor not stopping irrigation?
If the rain sensor on your Hunter Controller isn't stopping irrigation, make sure that the jumper wire on the SEN terminals is removed and that the sensor switch is set to the Active position.
Configure the controller's current date and time settings for accurate irrigation scheduling.
Define specific times for irrigation programs to begin, allowing multiple start times.
Remove or disable a previously set program start time to prevent unintended watering.
Allocate watering duration for each individual station or zone within a program.
Specify which days of the week the irrigation system will operate or remain off.
Choose watering schedules based on odd or even numbered days of the month.
Set watering to occur at specified intervals, defined by a number of days between watering cycles.
Modify watering run times by a percentage based on seasonal weather conditions.
Manually run a single irrigation station for a specified duration.
Initiate a pre-programmed irrigation cycle manually, station by station.
Quickly start a manual program or advance through stations during a manual cycle.
Run all stations sequentially for a predefined test duration to check functionality.
Temporarily disable all watering functions by setting the controller to the 'System Off' position.
Set the controller to skip watering for a specified number of days due to rain.
Temporarily override sensor input to allow watering even when a sensor condition is met.
Provides guidance on best practices for setting up irrigation programs, start times, and run times.
Restore the controller to factory default settings, erasing all programmed schedules and configurations.
Addresses error messages related to wiring or solenoid issues displayed on the controller screen.
Troubleshoots error codes indicating issues with P/MV wiring or solenoid components.
Resolves SmartPort® errors caused by electrical noise or incorrect wiring connections.
Diagnoses why the controller indicates watering but no water is delivered, checking wiring and water source.
Provides solutions for a display that is frozen or shows garbled information, often due to power surges.
Fixes issues where the rain sensor fails to halt irrigation, checking jumper wires and switch settings.
Solves problems where the controller runs stations continuously, usually due to excessive start times.
Allows specific stations to ignore sensor shutdowns, providing control over sensor-dependent watering.
Manages run times and soak periods to prevent runoff by segmenting watering cycles.
Introduces pauses between station watering to accommodate slow valves or tank recharging.
Postpones automatic seasonal adjustment changes from Solar Sync for a specified number of days.
Controls program visibility, allowing users to show or hide specific programs and start times.
Sets the number of days watering remains off after a sensor is activated and restored.
Displays the cumulative run time for all stations within a selected program start time.
Enables saving and restoring of all programmed irrigation information for backup or transfer.
Resets the controller to factory default settings, clearing all schedules and settings.
Performs a diagnostic check on all stations to identify potential wiring problems.
General| Brand | Hunter |
|---|---|
| Model | X-CORE XC-2 |
| Category | Controller |
| Language | English |
To Next Page
